MVME162-040机械备件
这样做或使用未经批准的零件或修改可能导致垫子系统无法达到其规定性能。服务如需服务和协助，请联系供应商。尺寸型号。周边装饰指定长度两件式周边装饰指定长度带电缆干线单元装饰指定长度保护电线导管指定长度控制单元 毫米英寸目录号。目录编号每周建议的常规检查和测试记录见第节。全面检查和测试记录见第节建议每月次。日期检查人注释日期检查人员注释图纸编号更改编号安装说明系列或更小框架尺寸的低惯量无刷伺服电机，目录号，主题页重要用户信息目录号说明关于系列低惯量电机开始之前安装电机产品尺寸电机负载力额定值连接器数据拆卸和安装轴键电机电缆和附件套件规格附加资源系列或较小框架尺寸自动化年月重要用户信息在安装配置操作或维护本产品之前，请阅读本文档以及有关本设备安装配置和操作的附加资源部分中列出的文档。除所有适用的法规和标准的要求外，用户还需要熟悉安装和接线说明。包括安装调整投入使用组装拆卸和维护在内的活动需要由经过适当培训的人员按照适用的实践规范进行。如果以制造商未规定的方式使用本设备，则设备提供的保护可能会受损。在任何情况下，自动化股份有限公司均不对因使用或应用本设备而导致的间接或后果性损害负责。本手册中的示例和图表仅用于说明目的。由于与任何特定安装相关的许多变量和要求，自动化股份有限公司无法根据示例和图表承担实际使用的责任。
Doing so or using unapproved parts or modifications may cause the mat subsystem to fail to achieve its specified performance. Service For service and assistance, please contact the supplier. Size and model. Perimeter decoration Specified length Two piece peripheral decoration Specified length Cable trunk unit decoration Specified length Protection wire conduit Specified length Control unit millimeters inches Catalog number. The recommended weekly routine inspection and test records for catalog number are given in section. See the recommended monthly times in section for comprehensive inspection and test records. Date Checker's Note Date Checker's Note Drawing Number Change Number Installation Instructions Series or smaller frame size low inertia brushless servo motor, catalog number, Important user information on the topic page Catalog number description About installing the motor before the start of a series of low inertia motors Product size Motor load force rating Connector data Removing and installing the shaft key Motor cable and accessory kit specifications Additional resources Series or smaller frame size Automation important user information Before installing, configuring, operating or maintaining this product, Please read this document and the documents listed in the Additional Resources section about the installation configuration and operation of this device. In addition to the requirements of all applicable codes and standards, users need to be familiar with the installation and wiring instructions. Activities including installation, adjustment, putting into use, assembly, disassembly and maintenance shall be carried out by appropriately trained personnel in accordance with applicable codes of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be damaged. In no case shall Automation Co., Ltd. be liable for indirect or consequential damages caused by the use or application of this equipment. The examples and diagrams in this manual are for illustrative purposes only. Due to the many variables and requirements associated with any particular installation, Automation GmbH cannot assume responsibility for actual use based on examples and diagrams.
