MVME162-12备件模块
检查机械安装检查传感器垫周边装饰件和联合装饰件是否完好无损，是否正确定位和固定。检查是否达到了设计的安全距离。检查除了通过垫子之外，是否无法进入危险区域，并且任何固定防护装置等是否根据设计进行了定位，并且是否安全。检查危险区和垫子系统之间是否有人。检查当前或可预见的环境条件是否符合设计阶段考虑的环境条件。检查安装是否无设计阶段未预见到的危险。检查所有警告通知是否到位。检查是否已安装所需的任何其他保护措施。检查电气功能确保垫子上没有人员和设备。暂时断开机器控制系统提供的任何自动复位功能。恢复机器电源，但确保机器原动机仍与机器最终接触器断开。仅手动模式使用控制单元时不相关检查控制单元绿色电源亮起绿色手动复位亮起复位按钮中的复位灯亮起红色机器启用关闭。。按下并松开重置按钮检查机器启用是否亮起，重置灯是否熄灭站在垫子上，检查机器启用的是否熄灭。离开机器，检查机器已启用是否熄灭，重置按钮是否点亮。按下并松开重置按钮，检查机器启用是否亮起，重置按钮是否熄灭。重复上述测试，检查远程重置按钮和指示灯如果安装。重复上述步骤，检查连接到垫子系统的任何状态监测的正确操作。仅限自动重置模式使用控制单元时不相关检查控制单元上的绿色电源亮起绿色机器已启用。站在垫子上，检查机器已启用是否熄灭。离开机器，检查机器启用是否亮起。。重复上述步骤，以检查连接到垫系统的任何状态监测的正确操作。控制单元功能仅自动重置模式。检查控制单元绿色电源亮起绿色机器启用亮起通道故障至亮起绿色，与安装的垫子数量相匹配。站在号垫子上，检查机器启用熄灭，信道故障变为红色。离开垫子，检查控制系统是否恢复到与上述第项相同的状态。对连接到控制单元的每个垫重复此过程，检查相应的通道故障是否变为红色。仅手动重置模式。检查控制单元绿色电源亮起绿色机器启用亮起通道故障至亮起绿色，与安装的垫数量相匹配。站在号垫子上，检查机器启用熄灭，通道故障变为红色。通过操作重置按钮关闭机器，手动重置系统，然后检查控制系统返回到与上述项目相同的状态。
Check the mechanical installation. Check whether the trim around the sensor pad and the joint trim are intact and correctly positioned and fixed. Check whether the designed safety distance is reached. Check whether it is impossible to enter the dangerous area except through the mat, and whether any fixed protective devices are positioned according to the design and safe. Check for people between the hazardous area and the mat subsystem. Check whether the current or foreseeable environmental conditions meet the environmental conditions considered at the design stage. Check whether the installation is free from dangers not foreseen at the design stage. Check that all warning notices are in place. Check that any other protective measures required have been installed. Check the electrical function to ensure that there are no people and equipment on the mat. Temporarily disconnect any automatic reset functions provided by the machine control system. Restore the machine power, but ensure that the machine prime mover is still disconnected from the final contactor of the machine. The manual mode only is irrelevant when using the control unit. Check the control unit. The green power is on. The green manual reset is on. The reset lamp in the reset button is on. The red machine is on. The machine is off.. Press and release the reset button to check whether the machine enabled is on, whether the reset lamp is off, stand on the mat and check whether the machine enabled is off. Leave the machine and check whether the machine is enabled and turned off, and whether the reset button is on. Press and release the reset button, and check whether the machine enabling is on and the reset button is off. Repeat the above test and check if the remote reset button and indicator are installed. Repeat the above steps to check the correct operation of any condition monitoring connected to the mat subsystem. Automatic reset mode only Not relevant when using the control unit Check that the green power on the control unit lights up Green machine is enabled. Stand on the mat and check that the machine is enabled and turned off. Leave the machine and check that the machine activation is lit.. Repeat the above steps in order to check the correct operation of any condition monitoring connected to the cushion system. The control unit function only automatically resets the mode. Check that the green power of the control unit lights up green The machine enable lights up the channel fault to light up green, matching the number of mats installed. Stand on the number mat and check that the machine is enabled and off, and the channel fault turns red. Leave the mat and check whether the control system is restored to the same state as item above. Repeat this process for each pad connected to the control unit and check whether the corresponding channel fault turns red. Manual reset mode only. Check that the green power of the control unit lights up green Machine enable lights up Channel fault lights up green, matching the number of pads installed. Stand on the No. mat and check that the machine is enabled and off, and the channel fault turns red. Shut down the machine by operating the reset button, reset the system manually, and then check that the control system returns to the same state as the above items.
