MVME162-202工控备件机器人模块
从控制单元到垫子的电线可以使用导线埋在地板中或通过边缘装饰件。此类安装建议使用挠性导管。详见第节。确定接线方法，并确定控制单元接线垫的输入和输出连接点。最终细节准备安装布局和电路的工作计划和图纸。建议将所有测量和计算记录并保存在机器的技术文件中。第节安装和调试开始安装前，应完整阅读本手册。开始工作前，请仔细学习本节内容。安装和调试应由系统设计师监督。需要一名熟悉工业布线实践的机械技术人员和一名电工进行安装。调试应由在安全安装方面有经验的训练有素的电气技术人员进行。需要以下专用工具预绝缘对接接头的压接工具图连接器例如图带热收缩反射器附件的热风枪如隔离并锁定机器电源。检查地板是否干净无碎屑，任何埋地管道或其他布线是否正确到位。拆开垫子，小心保持平整，不要拉扯电线。将垫子放置在地板上的计划位置，连接线位于检测区域的外围。根据图将垫段连接在一起。图注意垫线具有黑色外层。两个具有黑色内护套，两个具有白色内护套位置见图。控制单元处的传感器垫白黑白白黑黑黑黑黑黑白白黑终端留有足够的线尾长度，以便在更换垫的情况下重新制作连接，但确保互连线能够轻松地安装在边缘装饰件下，而不会压伤。使用下图所示的对接连接器连接电线。如果垫线需要延长，例如前垫到后垫连接和控制单元连接，则使用额外的一对对接连接器和一段双导线参见布线规范第节。图组合修剪固定安装中使用的所有活动组合修剪部分必须斜接至。这有助于安装，并有助于保持传感区域的整体灵敏度。图周边饰板固定如果控制单元的接线未埋置，则在电线入口和出口位置切割周边饰板，并切割饰板坡度以适合所选导管系统。小心完全开槽，以便周边装饰件的任何弯曲都不会夹住电线。确保没有可能损坏导线的锐边或毛刺。图进入电缆槽周边饰板底部的垫线建议切口的饰板固定件详图挠性导管入口建议切口的铝制内角周边饰板与和一起使用铝制外角周边饰条与及一起使用应力释放夹具挠性导管切口槽此处，在锋利的边缘上使用边缘护环剥下的电线并插入压接筒。使用压接工具上正确的空腔尺寸压接。使用带导流板的加热枪加热压接接头，直到管道收缩，粘合剂收缩并流动。和和对于外部拐角装饰件，使用。对于内部拐角装饰件使用，和使用带挠性导管的应力消除夹具将所有装饰件切割成，如图所示。
The wires from the control unit to the mat can be buried in the floor or through the edge trim using wires. Flexible conduit is recommended for such installations. See Section for details. Determine the wiring method, and determine the input and output connection points of the control unit wiring pad. Final details Prepare work plans and drawings for installation layout and circuits. It is recommended that all measurements and calculations be recorded and kept in the technical documentation of the machine. Section Installation and Commissioning This manual should be read completely before installation. Please study this section carefully before starting work. Installation and commissioning shall be supervised by the system designer. A mechanical technician familiar with industrial wiring practice and an electrician are required for installation. The commissioning shall be carried out by trained electrical technicians with experience in safe installation. The following special tools are required for crimping the pre insulated butt joint Fig. Connector, e.g. Fig. Hot air gun with heat shrinkable reflector accessories, e.g. isolating and locking the machine power supply. Check that the floor is clean and free of debris and that any buried piping or other wiring is in place. Remove the mat and be careful to keep it flat. Do not pull the wire. Place the mat at the planned position on the floor, and the connecting line is located at the periphery of the detection area. Connect the cushion sections according to the figure. Note that the padding line has a black outer layer. Two have black inner sheaths and two have white inner sheaths. The sensor pad white black white black black black black black black black black white black black white black black black white black terminal at the control unit has enough tail length to facilitate the connection when the pad is replaced, but ensure that the interconnect can be easily installed under the edge trim without crushing. Connect the wires using the butt connectors shown below. If the pad wire needs to be extended, such as the front pad to rear pad connection and the control unit connection, use an additional pair of butt connectors and a section of double wires. See Section of Wiring Specifications. All movable combination trim parts used in the figure combination trim fixing installation must be mitered to. This facilitates installation and helps maintain the overall sensitivity of the sensing area. Fig. Fixation of peripheral trim panel If the wiring of the control unit is not embedded, cut the peripheral trim panel at the wire inlet and outlet, and cut the trim panel slope to fit the selected conduit system. Be careful to fully slot so that any bending of the surrounding trim will not trap the wire. Make sure there are no sharp edges or burrs that could damage the wires. Fig. The padding line at the bottom of the peripheral trim panel of the cable tray. Details of the trim panel fastener with the recommended cut at the flexible conduit entrance. The aluminum inner corner peripheral trim panel with the recommended cut is used together with and. The aluminum outer corner peripheral trim strip is used together with and. The stress relief clamp is used in the flexible conduit cut slot. Here, use the edge guard ring to peel off the wires on the sharp edge and insert the crimping cylinder. Crimp with the correct cavity size on the crimping tool. Use a heat gun with a deflector to heat the crimp joint until the pipe shrinks and the adhesive shrinks and flows. And and for the exterior corner trim, use. For internal corner trim use, and use a stress relief fixture with flexible conduit to cut all trim into as shown.
