MVME162-222备件模块
周边修剪主动联合修剪传感器垫检测区每个周边修剪增加每个联合修剪接头增加标称垫尺寸每个周边修剪增加自攻螺钉未提供图尺寸单位为英寸不按比例。导轨使用盖子底部的固定孔聚碳酸酯外壳钢外壳和导轨外壳第节安装设计开始安装前，应完整阅读本手册。建议装置只能由电气和机械工程方面具有适当能力并具有安全相关控制系统设计经验的人员设计。许多因素有助于安全可靠的安装。通过以下步骤的工作，将确保不会忽略任何内容，并且可以以最小的麻烦和最大的信心规划和实施安装。所遵循的程序细节基于欧洲最佳实践，并符合欧盟机械指令。即使这些要求不适用于您的安装，我们建议您遵循相同的步骤，但修改细节以符合相关法定要求或实践规范例如。危险的性质当操作员在危险附近时，该系统可通过隔离电源消除危险。需要采取其他措施来处理风险评估中确定的其他危险例如零件喷射热表面等。这些措施可能包括固定防护联锁防护警告通知等。如果需要，请联系供应商获取更多信息。注风险评估包含在中，并在安全保护性质中详细说明。系统设计必须满足三个主要要求如果有人能够进入危险区域，则必须停止机器。在接近人员能够进入危险区域之前，机器必须停止。不得轻易绕过系统。建议使用垫子系统，可在可能进入危险区域的整个区域进行存在感测。参见图中的示例。不建议将垫子系统用于其他用途，例如，仅用作周界防护装置或机器启用装置。如果您正在考虑本手册未涵盖的任何应用的垫系统，请联系供应商。图环境和操作条件参考第节中给出的规范和本节中的信息，确保不存在可能影响系统完整性的不利因素。传感器垫乙烯基覆盖物的耐化学性垫覆盖物的耐水性卓越的乙醇卓越的氯化钠卓越的漂白一般来说，覆盖物具有良好的耐酸碱和耐盐性。热酸和碱以及浓酸和有机酸对长时间接触有有害影响。该覆盖物对脂肪族溶剂具有良好的耐受性，对芳香族和氯代溶剂的耐受性较差，复位执行机构应位于保护区外，且位置应确保危险和保护区清晰可见。在其他情况下，考虑到测试和维护的访问要求，控制单元可以安装在保护区外任何方便的地方。控制单元应安装在防护等级至少为的外壳内符合。
Peripheral trimming Active joint trimming Sensor pad Detection area Each peripheral trimming is increased Each joint trimming joint is increased Nominal pad size Each peripheral trimming is increased Self tapping screw is not provided Drawing size is not provided Unit is inch, not in proportion. The guide rail uses the fixing hole at the bottom of the cover, the polycarbonate housing, the steel housing and the guide rail housing. Section Installation Design. Before installation, you should read this manual completely. It is recommended that the device be designed only by personnel with appropriate competence in electrical and mechanical engineering and experience in the design of safety related control systems. Many factors contribute to a safe and reliable installation. The following steps will ensure that nothing will be ignored and the installation can be planned and implemented with minimum trouble and maximum confidence. The details of the procedures followed are based on European best practices and comply with the EU Machinery Directive. Even if these requirements do not apply to your installation, we recommend that you follow the same steps, but modify the details to comply with relevant statutory requirements or codes of practice, for example. The nature of the hazard When the operator is near the hazard, the system can eliminate the hazard by isolating the power supply. Other measures need to be taken to deal with other hazards identified in the risk assessment, such as parts spraying hot surfaces. These measures may include fixed protection interlocking protection warning notice, etc. If necessary, please contact the supplier for more information. NOTE Risk assessments are included in and are detailed in the Nature of Security Protection. The system design must meet three main requirements If someone can enter the hazardous area, the machine must be stopped. The machine must be stopped before approaching personnel can enter the hazardous area. Do not bypass the system easily. It is recommended to use a mat system that can sense presence throughout the area that may enter the hazardous area. See the example in Illustration. It is not recommended to use the mat subsystem for other purposes, such as perimeter guards or machine activation devices only. If you are considering pad systems for any application not covered in this manual, please contact the supplier. Refer to the specifications given in section and the information in this section for the environmental and operating conditions of the diagram to ensure that there are no adverse factors that may affect the integrity of the system. Chemical resistance of the sensor pad vinyl cover pad cover excellent water resistance excellent ethanol excellent sodium chloride excellent bleaching Generally speaking, the cover has good acid and alkali resistance and salt resistance. Hot acid and alkali as well as concentrated acid and organic acid have harmful effects on long-term contact. The cover has good resistance to aliphatic solvents, but poor resistance to aromatic and chlorinated solvents. The reset actuator should be located outside the protection area, and the location should ensure that the danger and protection area are clearly visible. In other cases, considering the access requirements for testing and maintenance, the control unit can be installed at any convenient place outside the protected area. The control unit shall be installed in an enclosure with a protection level of at least.
