MVME162-243工控模块系统备件
该系统只能在给定的规格范围内使用，并严格按照本手册中提供的信息进行安装。该系统本身不能提供保护，以防止因物质气体和辐射的喷射而产生的危险。对于这些应用，可能需要额外的保护措施，如物理防护。该系统不打算用作外围防护。该系统不打算用作机器启动或重新启动装置。机器控制电路的配置必须确保系统输出触点的闭合能够启动机器的启动电路，但不会直接导致机器启动。机器的启动或重新启动只能通过在指定的机器控制装置上进行单独的故意操作来实现。该系统不适用于爆炸性环境。如果需要有关系统适用于特定应用的进一步指导，请联系供应商。用作组合跳闸和存在传感系统图用作组合跳闸与存在传感系统。该系统允许操作员和某些类型的车辆清晰地查看过程，不受阻碍地进入。必须有足够的空间，以确保从危险区到可接近的垫子周边的最小距离符合第节中给出的安全距离计算。所定义的周边和危险区之间的整个地面区域必须由垫子传感器覆盖，以便在不启动垫子系统的情况下无法接近或接近危险区。危险垫用作防护周界内的存在感测系统图用作防护周界中的存在感系统。该系统提供存在感测，以防止人员在封闭区域内时机器启动的任何可能性。当系统以这种方式用作二级保护系统时，第节中给出的安全距离计算不适用。周界防护方法应符合所有相关要求。封闭周界和危险区域之间的整个地面区域必须由垫子传感器覆盖，以便人员在不启动垫子系统的情况下无法进入封闭区域。
The system can only be used within the given specification range, and shall be installed in strict accordance with the information provided in this manual. The system itself cannot provide protection against hazards arising from the ejection of material gases and radiation. For these applications, additional protective measures, such as physical protection, may be required. The system is not intended for perimeter protection. The system is not intended to be used as a machine starting or restarting device. The configuration of the machine control circuit must ensure that the closing of the system output contacts can start the starting circuit of the machine, but will not directly cause the machine to start. The starting or restarting of the machine can only be achieved through separate intentional operation on the designated machine control device. The system is not suitable for explosive environments. If you need further guidance on the suitability of the system for a particular application, please contact the supplier. Used as a combined trip and presence sensing system diagram used as a combined trip and presence sensing system. The system allows the operator and certain types of vehicles to see the process clearly and enter unhindered. There must be sufficient space to ensure that the minimum distance from the danger zone to the perimeter of the accessible mat complies with the safety distance calculation given in Section. The entire ground area between the defined perimeter and the hazard area must be covered by a mat sensor so that the hazard area cannot be approached or approached without activating the mat system. The hazard pad is used as the presence sensing system in the protective perimeter The map is used as the presence sensing system in the protective perimeter. The system provides presence sensing to prevent any possibility of the machine starting when a person is in an enclosed area. When the system is used as a secondary protection system in this way, the safety distance calculation given in Section does not apply. The method of perimeter protection shall comply with all relevant requirements. The entire ground area between the enclosed perimeter and the hazardous area must be covered by mat sensors so that personnel cannot enter the enclosed area without activating the mat system.
