MVME162-432机械备件
表示显示的行参见第页的图。按下重要提示适用于以太网固件版本为及更高版本的装置。年月通信第章在应用程序中添加新模块时，安装文件后，模块将显示在目录号下。要使用附加模块配置文件，请执行以下步骤。选择的目录号，然后单击创建。输入电源监视器的名称和地址。单击模块定义下的更改。模块定义窗口打开。默认情况下，第一个连接设置为仅输入。年月第章通信单击连接名称单元格打开第一个连接可用选项的下拉菜单。表可用连接连接名称描述数据访问模块定义的数据类型大小字节标记后缀仅输入产品信息组件实例读取:仅侦听仅输入实时电压和电流读取:仅侦听:仅输入实时功率，频率读取:只侦听:仅输入最大电压和电流读取:[:只侦听:仅输入最大功率，频率读取:仅侦听:仅输入所需电压和电流读取:[:只侦听，频率读取:仅侦听:仅输入能量读取:[:只侦听:仅输入报警和输出状态读取:[号]:仅侦听:在仅输入时使用仅侦听连接与另一个控制器存在连接。其中是模块定义中配置的连接号。年月通信第章要选择多个输入实例，请单击名称列下的下一个可用单元格，打开下拉选择列表并选择所需的连接。最多可以从表所示的选项中选择九个连接。选择连接后，单击确定。单击是更改模块定义。年月第章通信在连接上输入所需的请求分组间隔。默认为。请勿为装置输入小于的。单击确定创建模块。创建模块时，将为在模块定义中选择的每个连接名称生成控制器标记。年月通信第章在本示例中，为实例和创建控制器标签。仅输入连接不需要存在独占所有者连接。仅输入连接允许您使用显示器通信或软件配置工具配置电源监视器。通用以太网模块输入数据连接具有通信的单元支持到九个组件实例的类连接。要使用控制器配置到选定部件实例的连接，请执行以下步骤。在应用程序中脱机打开控制器程序如果使用的是控制器，则在程序模式下联机。在配置树中，右键单击以太网通信模块例如，然后选择新建模块。从通信下拉菜单中选择以太网模块通用以太网模块。标记后缀连接编号模块定义连接组件实例控制器标记创建的模块定义数据类型创建的仅输入:仅输入:仅输入:[编目号]:输入标记由和一位组成，用于监视与设备的连接。年月第章通信输入此对话框中列出的设置参数，并在表中进行说明。
The displayed rows are shown in the figure on page. Press Important for devices with Ethernet firmware version and later. When a new module is added to the application program in the chapter of the month and month communication, the module will be displayed under the directory number after installing the file. To use an add in profile, perform the following steps. Select the catalog number of and click Create. Enter the name and address of the power monitor. Click Change under Module Definition. The module definition window opens. By default, the first connection is set to input only. Month Month Chapter Communication Click the connection name cell to open the drop-down menu of the available options for the first connection. Table The connection name can be used to describe the data type size defined by the data access module Byte tag suffix Only input product information Component instance reading: Only listen Only input real-time voltage and current Reading: Only listen: Only input real-time power, Frequency reading: only listen: only input the maximum voltage and current reading: [: only listen: only input the maximum power, frequency reading: only listen: only input the required voltage and current reading: [: only listen, frequency reading: only listen: only input energy reading: [: only listen: only input the alarm and output status reading: [number]: only listen: only use the only listen connection to have a connection with another controller when only input. Where is the connection number configured in the module definition. In the chapter of Monthly Communication, to select multiple input instances, click the next available cell under the name column, open the drop-down selection list, and select the required connection. You can select up to nine connections from the options shown in the table. After selecting a connection, click OK. Click Yes to change the module definition. The required request packet interval shall be input on the connection in Chapter Communication. The default is. Do not enter less than for the device. Click OK to create the module. When you create a module, a controller tag is generated for each connection name selected in the module definition. Month Month Communication Chapter In this example, create a controller label for the instance and. Input only connections do not require an exclusive owner connection. Input only connections allow you to configure the power monitor using monitor communications or software configuration tools. Universal Ethernet module input data connection The unit with communication supports class connection to nine component instances. To configure a connection to a selected assembly instance using a controller, perform the following steps. Open the controller program offline in the application If you are using a controller, you are online in program mode. In the configuration tree, right-click Ethernet communication module, for example, and select New Module. Select Ethernet moduleUniversal Ethernet module from the Communications drop-down menu. Tag suffix connection number module definition connection component instance controller tag created module definition data type created input only: input only: input only: [catalog number]: input tag consists of and, used to monitor the connection with the device. Enter the setting parameters listed in this dialog box and describe them in the table.
