MVME162-433，DCS工控模块备件
每次按下按钮时，触摸图标都会打开。我们建议使用食指激活触摸按钮。在计量模式下，按钮和如图所示用于显示所显示测量值的最大值和需求值平均值。图前面板显示项目描述活动警报状态指示灯。实际能耗率状态指示器。闪烁速度越快表示消耗率越高。根据退出按钮，最大频率为快速按下退出子菜单或退出编程模式下的编程菜单。在编程过程中，按住退出至少秒以退出编程菜单。按确认并返回计量显示，然后退出编程菜单，而不保存更改。要保存更改，请使用向上和向下箭头转到结束菜单，然后按程序选择。不在编程中时，按住秒以上可查看信息页面。在计量模式下，快速按下可滚动查看能量计数器。向上按钮按向上按钮浏览菜单并增加要设置的值。向下按钮按下向下按钮浏览菜单并减少要设置的值。程序选择按钮按住程序选择按钮至少秒以访问编程菜单。在编程过程中，按下编程选择确认激活页面中的编程值。按程序选择进入和退出活动页面上的编辑模式。如果不在编程中，则按程序选择选择要显示的测量值。快速按下可在计量显示页面中滚动。测量屏幕列表见表和表。年月第章单元概述附加按钮功能某些按钮有两种功能。要访问第二个功能，请按住按钮秒钟以上。显示信息屏幕，提供参考标准固件版本和制造年份。重置显示变量的最大值。您必须按确认重置。重置显示变量的需求。您必须按确认重置。年月单元概述第章显示功能图功能显示图标报警图标指示高值报警指示低值报警显示项描述相移指示器电感或电容。该标志基于实际潮流的方向。正消耗功率，负发电功率。有关更多信息，请参见附录中功率和功率因数的几何表示。在编程模式下，当可以编辑参数时，指示器显示。表示测量值相位线到中性点或线到线。表示测量值相位线到中性点或线到线。表示测量值相位线到中性点或线到线。工程单位和乘数指示器，。报警显示功能激活。编程功能激活。为能量计数器留出的区域见表文本消息日期和时间格式:。表示计量值为需求或最大值。显示项目说明表示显示的计量值为系统三相值。表示电压旋转的相序错误报警。配置锁定开关未激活。始终表示已解锁。串行数据传输和接收的指示。年月第章装置概述选择要显示的数据表和表提供了导航前面板显示器上可用的计量数据显示的指南。
Each time the button is pressed, the touch icon opens. We recommend using the index finger to activate the touch button. In metering mode, the buttons and, as shown in the figure, are used to display the maximum value of the displayed measured value and the average value of the demand value. Figure The front panel shows the item description active alarm status indicator. Actual energy consumption rate status indicator. The faster the flashing speed is, the higher the consumption rate is. According to the exit button, the maximum frequency is to quickly press to exit the submenu or exit the programming menu in the programming mode. During programming, press and hold Exit for at least seconds to exit the programming menu. Press OK and return to the metering display, then exit the programming menu without saving the changes. To save your changes, use the up and down arrows to go to the end menu and press Program Select. When not in programming, press and hold for more than seconds to view the information page. In metering mode, press briefly to scroll through the energy counters. Up ButtonPress the up button to navigate through the menu and increase the value to be set. Down ButtonPress the down button to navigate through the menu and decrease the value to set. Program selection button Press and hold the program selection button for at least seconds to access the programming menu. During programming, press Programming Select to confirm the programmed value in the active page. Press Program Select to enter and exit edit mode on the active page. If it is not in programming, select the measurement value to be displayed according to the program selection. Press briefly to scroll through the metering display page. The list of measurement screens is shown in Table and Table. Year Month Chapter Unit Overview Additional Button Functions Some buttons have two functions. To access the second function, press and hold the button for more than seconds. The information screen is displayed, providing the reference standard firmware version and year of manufacture. Reset the maximum value of the display variable. You must press OK to reset. Reset the demand for display variables. You must press OK to reset. Year Month Unit Overview Chapter Display Function Chart Function Display Icon Alarm Icon Indication High Value Alarm Indication Low Value Alarm Display Item Description Phase Shift Indicator Inductance or Capacitance. This sign is based on the direction of the actual current. Positive power consumption, negative power generation. For more information, see the geometric representation of power and power factor in the appendix. In programming mode, the indicator displays when the parameter can be edited. Indicates the measured value phase line to neutral or line to line. Indicates the measured value phase line to neutral or line to line. Indicates the measured value phase line to neutral or line to line. Engineering Units and Multiplier Indicators,. The alarm display function is activated. The programming function is active. The area reserved for the energy counter is shown in the table Text Message Date and Time Format:. Indicates that the measured value is demand or maximum value. The displayed item description indicates that the displayed metering value is the three-phase value of the system. Indicates the phase sequence error alarm of voltage rotation. The configuration lockout switch is not active. Always indicates unlocked. Indication of serial data transmission and reception. Year Month Chapter Device Overview Selecting the data tables and tables to display provides guidelines for displaying the metering data available on the navigation front panel display.
