MVME162-512A工业卡件
反馈和引脚描述引脚高分辨率编码器高分辨率编码器增量编码器引脚和相功率相位和功率相位也可以分别标记为和。相相接地数据数据保留数据数据保留保留保留保留公共公共连接器保留保留公共保留保留反馈连接器系列或更小框架尺寸的低惯量无刷伺服电机年月拆除和安装轴键轴键由钢制成。指定的公差为安全和刚性连接提供过盈配合略大于开口。要取下轴键，请执行以下操作之一用钳子或类似工具抓住键，将其抬起。将螺丝刀插入钥匙和插槽之间，撬起钥匙。要安装轴键，请执行以下步骤。在继续操作之前，确认替换键与轴中的键槽和匹配的机械连接例如，联轴器或滑轮相匹配。将键的前部与电机轴的前部对齐。这可防止键槽电机端的弧形切割端干扰键的正确定位。用夹具支撑轴直径的下侧，并使用受控的按压装置在顶面施加恒定的力，将键压入轴中。轴键安装注意事项安装或拆卸轴键时，不要用工具敲击电机的轴联轴器或滑轮。如果在安装联轴器和皮带轮或拆除轴键时对轴施加剧烈冲击，或者从电机安装面施加杠杆以拆除安装在电机轴上的装置，则可能会损坏电机轴承和反馈装置。用车轮拉拔器向轴的用户端施加恒定压力，以移除摩擦配合或卡住的装置。用于电机支架的键槽键轴支架的键对齐径向切口系列低惯量无刷伺服电机，具有或更小的框架尺寸年月电机电缆和附件套件本节介绍了系列低惯性电机可用的附件。电机电缆工厂制造的反馈电缆和电力电缆有标准电缆长度。它们提供了实现环境等级和屏蔽端接所需的密封。有关可用电缆的完整列表请联系最近的销售办事处或参考运动配件规格技术数据。轴封套件轴封是一种屏障，可以防止水分和颗粒进入电机轴承。轴封容易磨损，需要定期检查和更换。根据使用情况，建议每个月更换一次，但不超过个月。表中列出了电机的目录号和相应的更换丁腈轴密封套件。有关如何安装轴封的说明，请参阅轴封套件安装说明。重要事项轴封必须润滑。润滑剂随轴封套件提供。第三方轴封不允许与这些电机一起使用。
Feedback and pin description pins High resolution encoder High resolution encoder Incremental encoder pin and phase power phase and power phase can also be marked as and respectively. Phase grounding data data retention data retention retention retention retention public public connector retention retention public retention retention feedback connector series or smaller frame size low inertia brushless servo motor year month remove and install shaft key shaft key made of steel. The specified tolerance provides an interference fit slightly greater than the opening for safe and rigid connections. To remove the shaft key, do one of the following to grasp the key with pliers or a similar tool and lift it. Insert a screwdriver between the key and the slot and pry up the key. To install the shaft key, perform the following steps. Before continuing, confirm that the replacement key matches the keyway in the shaft and the matching mechanical connection, such as coupling or pulley. Align the front of the key with the front of the motor shaft. This prevents the arc-shaped cutting end of the motor end of the keyway from interfering with the correct positioning of the key. Use a jig to support the lower side of the shaft diameter, and use a controlled press device to apply a constant force on the top surface to press the key into the shaft. Precautions for shaft key installation When installing or removing the shaft key, do not use tools to knock the shaft coupling or pulley of the motor. The motor bearing and feedback device may be damaged if severe impact is exerted on the shaft when installing the coupling and pulley or removing the shaft key, or lever is applied from the motor mounting surface to remove the device installed on the motor shaft. Use a wheel puller to apply constant pressure to the user end of the shaft to remove friction fits or stuck devices. Keyway for motor support Keyway for key shaft support Key alignment Radial notch series low inertia brushless servo motor with or less frame size Year motor cable and accessory kit This section describes the accessories available for series low inertia motors. The feedback cable and power cable manufactured by the motor cable factory have standard cable lengths. They provide the seals required to achieve environmental ratings and shield terminations. For a complete list of available cables, contact the nearest sales office or refer to the sports accessory specifications technical data. Shaft seal kit The shaft seal is a barrier that prevents moisture and particles from entering the motor bearings. The shaft seal is easy to wear and needs regular inspection and replacement. According to the service condition, it is recommended to replace it once a month, but not more than months. Table lists the catalog number of the motor and the corresponding replacement nitrile shaft seal kit. For instructions on how to install the shaft seal, refer to the shaft seal kit installation instructions. Important The shaft seal must be lubricated. Lubricant is supplied with the shaft seal kit. Third party shaft seals are not allowed to be used with these motors.
