MVME162-513A系统模块卡件
如果无法拧紧连接器，请验证键控连接器是否正确对齐。不要使用工具例如钳子和虎钳拧紧接头。制动器和电源连接器反馈连接器对齐平面对齐平面系列或更小框架尺寸的低惯量无刷伺服电机年月产品尺寸本节提供了电机的尺寸。见详图±±轴直径公差电机，电机Ö详图轴直径和电机▸连接器反馈连接器直径螺栓圆上的直径孔尺寸单位为轴端螺纹孔电机螺纹螺纹深度，电机螺纹螺纹深度连接器外壳可在导向直径公差范围内旋转电机▸电机，键系列低惯量无刷伺服电机，具有或更小的框架尺寸年月和电机尺寸电机设计为公制尺寸。英寸尺寸是毫米的近似换算。无公差的尺寸仅供参考。电机类别。编号如果订购带制动器的或电机，则在尺寸和上增加在和上增加如果订购带制动器的或电机，则尺寸和增加和增加此尺寸的公差为±±键槽轴直径和导向直径公差见第页。。毫米英寸毫米英寸。公差和补充尺寸电机负载力额定值电机能够在持续的轴负载下运行。图中显示了径向和轴向负载力的位置，并列出了最大值。载荷以磅千克为单位进行测量，这是数学转换。轴上的负载力下表表示了各种负载和速度下的小时轴承疲劳寿命。这小时的使用寿命没有考虑到因轴承磨损可能导致的特定应用寿命减少来自外部的油脂污染。和键槽公差轴跳动导向偏心度最大端面跳动键槽深度键槽宽度径向负载力额定值电机类别。编号，最大速度磅轴向负载力径向负载力施加在轴延伸中心。系列或更小框架尺寸的低惯量无刷伺服电机年月轴向负载力额定值最大径向负载电机类别。编号，最大速度电机类别。转/分转/分转/分转/分，最大速度磅系列或更小框架尺寸的低惯量无刷伺服电机年月连接器数据本表提供了连接器上的反馈电源和制动引脚的信号说明。
If the connector cannot be tightened, verify that the keyed connector is properly aligned. Do not use tools such as pliers and vises to tighten the connector. Brake and power connector feedback connector alignment plane alignment plane series or lower frame size low inertia brushless servo motor monthly product size This section provides the motor size. See the detail drawing ± ± axis diameter tolerance motor. The motor shaft diameter and motor connector feedback connector diameter. The diameter hole size on the bolt circle is the shaft end threaded hole. The motor thread thread depth. The connector shell can rotate the motor within the guide diameter tolerance. The key series low inertia brushless servo motor has or smaller frame size. The motor is designed as metric size. Inch dimensions are approximate conversions of millimeters. Dimensions without tolerances are for reference only. Motor category. No. If ordering a braked or motor, add dimensions and to add dimensions and If ordering a braked or motor, the tolerance for dimensions and adding and adding this dimension is ± ± the tolerance for keyway shaft diameter and guide diameter see page.. Millimeters inches millimeters inches. Tolerances and supplementary dimensions Motor load force ratings The motor is capable of operating under continuous axle load. The figure shows the location of the radial and axial load forces and lists the maximum values. The load is measured in pounds and kilograms, which is a mathematical conversion. The following table shows the hourly bearing fatigue life under various loads and speeds. The service life of this hour does not take into account the specific service life that may be reduced due to bearing wear from external grease contamination. And keyway tolerance shaft runout pilot eccentricity maximum end face runout keyway depth keyway width radial load force rating motor category. No., maximum speed pounds axial load force radial load force is applied to the shaft extension center. Series or smaller frame size low inertia brushless servo motor Monthly axial load force rating Maximum radial load motor category. Number, maximum speed motor category. Revolution/minute revolution/minute revolution/minute revolution/minute revolution/minute, maximum speed pounds series or lower frame size low inertia brushless servo motor monthly connector data This table provides the signal description of the feedback power supply and brake pin on the connector.
