MVME162-522工业卡件
电机制动电路中的电弧抑制驱动器具有包括电弧抑制器的制动控制继电器。在这种情况下，不需要客户提供的电弧抑制，除非制动器的功耗需要外部制动器继电器。电力电缆内的屏蔽信号线两条整体电力电缆屏蔽回路信号屏蔽两条中的一条至总体电力电缆屏蔽工厂提供的现场修改验证驱动器上的电源电缆接地夹是否接触所有三个电缆屏蔽。直流电源客户提供的部件制动继电器二极管或电弧抑制器系列低惯量无刷伺服电机，具有或更小的框架尺寸年月安装电机系列电机包括用于将电机对准机器的安装导向器。优选的紧固件为不锈钢。安装必须符合所有当地法规，并使用促进安全和电磁兼容性的设备和安装实践。更改连接器方向您可以将连接器外壳旋转。这使您可以将连接器调整到最佳位置，以保护连接免受可能的环境污染，同时提供电缆接入。圆形连接器外壳可沿任一方向旋转。按照以下步骤旋转连接器。在馈线上安装一根配套电缆并将其完全固定或动力制动接头。用手抓住配合的连接器和电缆插头，并将其缓慢旋转至电机外部。对另一个接头重复这些步骤。注意如果通电，未安装的电机断开的机械联轴器松脱的轴键和断开的电缆是危险的。锁定并标记拆卸的设备限制电源。向电机通电前，取下轴键和其他可能从轴上抛出的机械联轴器。注意确保电缆已安装并受到约束，以防止电缆连接处的不均匀张力或弯曲。当电缆弯曲时，电缆上过大且不均匀的横向力会抑制环境密封。The arc suppression driver in the motor brake circuit has a brake control relay including an arc suppressor. In this case, the arc suppression provided by the customer is not required, unless the power consumption of the brake requires an external brake relay. Shielded signal line in the power cable One of the two overall power cable shielded loop signal shields goes to the on-site modification provided by the overall power cable shield factory to verify whether the power cable grounding clip on the drive contacts all three cable shields. DC Power Customer Supplied Components Brake Relay Diode or Arc Suppressor Series Low Inertia Brushless Servo Motor, with or less frame size Year Month Mounting Motor Series Motors include mounting guides for aligning the motor to the machine. The preferred fastener is stainless steel. The installation must comply with all local regulations and use equipment and installation practices that promote safety and electromagnetic compatibility. Changing the connector orientation allows you to rotate the connector housing. This allows you to adjust the connector to the optimal position to protect the connection from possible environmental pollution while providing cable access. The circular connector housing can be rotated in either direction. Follow these steps to rotate the connector. Install a matching cable on the feeder and fix it completely or power brake connector. Grasp the mating connector and cable plug by hand and slowly rotate them to the outside of the motor. Repeat these steps for the other connector. Note that if the motor is powered on, the loose shaft keys and the disconnected cables of the disconnected mechanical coupling of the unmounted motor are dangerous. Lock and mark the removed device to limit power supply. Before energizing the motor, remove the shaft key and other mechanical couplings that may be thrown from the shaft. Care shall be taken to ensure that cables are installed and restrained to prevent uneven tension or bending at cable connections. When the cable is bent, excessive and uneven lateral forces on the cable will inhibit environmental sealing.
