MVME162-523工控机器人备件
目视检查电机有无损坏。检查电机框架前输出轴和安装导向器是否有任何缺陷。立即通知承运人任何运输损坏。保留原始包装材料，以防您需要将产品退回维修或运输到其他位置。使用内包装箱和外包装箱为单位退货提供足够的保护用于维修。在第页规范中列出的环境条件下，将电机存放或操作在清洁干燥的地方。取下轴盖用手取下安装在电机轴上的保护盖或用螺丝刀撬开盖。不要使用锤子或其他工具，因为它们会损坏电机轴。注意为避免人身伤害和电机损坏，请勿通过电机轴提升或搬运电机。轴上的盖子可能松动，导致电机掉落。注意不要试图打开和修改电机。本手册介绍了可在现场进行的修改。请勿执行本手册中未描述的修改。只有授权的维修中心才能维修此项目。请参阅支持部门以获取查找最近维修中心的帮助。系列或更小框架尺寸的低惯量无刷伺服电机年月延长电机寿命适当的设计和维护可以延长伺服电机的寿命。遵循这些准则，以最大限度地延长伺服电机在您环境中的使用寿命始终在每条电缆中提供滴水环，以将液体从电机连接处带走。如果可能，提供防护罩，以保护电机外壳轴封及其连接处免受异物或液体污染。轴封容易磨损，需要定期检查和更换。根据使用情况，建议每个月更换一次，但不超过个月。有关更多信息，请参阅第页的轴封套件。定期检查电机和密封件有无损坏或磨损。如果发现损坏或过度磨损，请更换该部件。该伺服电机上的制动器选项是一个弹簧组保持制动器，当向制动线圈施加电压时，该制动器会释放。分离制动器需要单独的电源。该电源可以通过伺服电机控制器或手动操作员控制来施加。
Visually inspect the motor for damage. Check the motor frame front output shaft and mounting guide for any defects. Notify the carrier immediately of any transport damage. Keep the original packaging materials in case you need to return the product for repair or transport to another location. Use inner and outer packing boxes to provide adequate protection for unit returns for maintenance. Store or operate the motor in a clean and dry place under the environmental conditions listed in the specifications on page. Remove the shaft cover Remove the protective cover installed on the motor shaft by hand or pry off the cover with a screwdriver. Do not use hammers or other tools as they will damage the motor shaft. To avoid personal injury and motor damage, do not lift or handle the motor through the motor shaft. The cover on the shaft may be loose, causing the motor to fall. Be careful not to attempt to open and modify the motor. This manual describes the modifications that can be made on site. Do not perform modifications not described in this manual. Only authorized service centers can repair this item. Refer to Support for help finding the nearest service center. Series or smaller frame size low inertia brushless servo motor can prolong the service life of the motor. Proper design and maintenance can prolong the service life of the servo motor. Follow these guidelines to maximize the service life of the servo motor in your environment Always provide a drip loop in each cable to take liquid away from the motor connection. If possible, provide a protective cover to protect the motor housing shaft seal and its connections from foreign matter or liquid contamination. The shaft seal is easy to wear and needs regular inspection and replacement. According to the service condition, it is recommended to replace it once a month, but not more than months. For more information, refer to the shaft seal kit on page. Regularly check the motor and seals for damage or wear. If damage or excessive wear is found, replace the component. The brake option on this servomotor is a spring set to hold the brake, which releases when voltage is applied to the brake coil. Separate power is required to disengage the brake. The power supply can be applied through servo motor controller or manual operator control.
