MVME162PA-252LSE工控DCS系统备件
除所有适用的法规和标准的要求外，用户还需要熟悉安装和接线说明。包括安装调整投入使用组装拆卸和维护在内的活动需要由经过适当培训的人员按照适用的实践规范进行。如果以制造商未规定的方式使用本设备，则设备提供的保护可能会受损。在任何情况下，罗克韦尔自动化股份有限公司均不对因使用或应用本设备而导致的间接或后果性损害负责。本手册中的示例和图表仅用于说明目的。由于与任何特定安装相关的许多变量和要求，罗克韦尔自动化股份有限公司无法根据示例和图表承担实际使用的责任。罗克韦尔自动化股份有限公司对本手册中所述的信息电路设备或软件的使用不承担任何专利责任。未经罗克韦尔自动化股份有限公司书面许可，严禁复制本手册的全部或部分内容。.触点的“架”状态为常开触点或常闭触点。.在给定开关位置，白色或黑色执行器下方的凸轮位置。注意，在第页的表中，标准选择开关凸轮代码的目标表以及凸轮代码和是相同的，无论接触块安装在白色执行器还是黑色执行器后面。凸轮代码和具有所有六种触点组合。每个标准和旋钮操纵杆操作员在工厂装配有一个白色插件。机翼操纵杆操作员为标准灰色。如果在工厂订购个或更多装置，则可提供其他颜色。对于标准和旋钮操纵杆操作员，请从下表中选择一个颜色代码字母。在列出的目录号中破折号后的第一个字母后插入颜色代码字母。例如，带有绿色插入件的将变为。代码字母颜色红色绿色蓝色黄色对于红色翼杆操纵器仅提供灰色或红色，将字母替换为字母。若要订购未安装彩色嵌件的标准或旋钮杆操作器，请在所列目录号破折号后的第一个字母后添加字母。包含其中一个的特殊包装不收取额外费用。目标表特殊颜色公告油密选择开关产品数据选择特殊照明选择开关与选择特殊非照明选择开关类似。然而，照明设备的接触块只能安装在白色致动器后面。
In addition to the requirements of all applicable codes and standards, users need to be familiar with the installation and wiring instructions. Activities including installation, adjustment, putting into use, assembly, disassembly and maintenance shall be carried out by appropriately trained personnel in accordance with applicable codes of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be damaged. Under no circumstances shall Rockwell Automation Co., Ltd. be liable for indirect or consequential damages caused by the use or application of this equipment. The examples and diagrams in this manual are for illustrative purposes only. Due to the many variables and requirements associated with any particular installation, Rockwell Automation Inc. cannot assume responsibility for actual use based on examples and diagrams. Rockwell Automation Co., Ltd. assumes no patent liability for the use of information circuit equipment or software described in this manual. Reproduction of this manual in whole or in part is strictly prohibited without the written permission of Rockwell Automation Co., Ltd The "rack" state of the contact is normally open or normally closed Cam position below the white or black actuator at a given switch position. Note that in the table on page, the target table of the cam code of the standard selector switch and the cam code and are the same, regardless of whether the contact block is installed behind the white actuator or the black actuator. Cam codes and have all six contact combinations. Each standard and rotary lever operator is factory equipped with a white insert. The wing joystick operator is standard gray. Other colors are available if units or more are ordered at the factory. For standard and rotary lever operators, select a color code letter from the following table. Insert the color code letter after the first letter after the dash in the listed catalog number. For example, with a green insert, becomes. The code letter color red green blue yellow is only available in gray or red for red wing lever manipulators, replace the letter with a letter. To order standard or rotary lever operators without color inserts, add a letter after the first letter after the dash of the catalog number listed. There is no extra charge for special packaging containing one of them. Special color announcement of target table Oil tight selector switch Product data selection Special lighting selector switch is similar to special non lighting selector switch. However, the contact block of the lighting fixture can only be mounted behind the white actuator.
