MVME172-432工控自动化卡件
任一接线通道中的单一故障将导致垫子控制单元锁定安全输出，直到故障得到纠正并重置控制单元。检查系统中的所有连接导线是否正确配置且未损坏，两个接触器是否正常工作。排除所有故障，如果处于手动复位模式，则按下并释放控制单元复位按钮。4.如果问题未得到解决，请联系供应商。38 8.5.2症状–机器无法停止或可以在垫子上启动。不允许使用机器1。如果垫子上有机器，垫子控制单元上的机器启用LED是否点亮？2.如果MACHINE ENABLED LED（机器启用LED）未亮起，则机器或其控制系统在垫系统外部可能存在故障。–在排除和测试故障之前，不得使用机器。3.如果机器启用LED亮起。-不允许使用机器，并立即联系供应商。8.5.3症状–机器在传感器垫上不存在的情况下意外停止，但可以在踩下垫后重新启动（并在手动重置模式下重置）。1.检查所有指示灯是否正常工作。如果是这样的话，问题很可能是由某个值和持续时间的供电下降引起的。这可能会导致控制单元中的一个内部继电器断开，从而模拟故障状况。这是极不可能发生的情况，不需要采取补救措施。在问题持续存在的异常情况下，可能需要采取措施以确保向垫子系统提供更顺畅的电源。8.6维修在垫系统或机器控制系统上工作之前，隔离机器和垫系统的电源。
遵守电气安全预防措施。用户维修仅限于更换新的垫系统部件。如果出现问题，应将装置退还给供应商。应使用推荐的对接拼接接头对连接线进行任何维修。篡改零部件将使保修失效。如果DIN导轨控制单元上的质量封条损坏，则保修无效。39可用备件对于特殊尺寸的传感器垫，请参阅标签上打印的型号。更换任何零件后，必须进行8.2所示的检查和测试，并特别注意更换的零件。警告：维护或维修操作后，必须正确重新安装所有镶边、紧固件和电缆保护装置。不这样做或使用未经批准的零件或修改可能导致垫子系统无法达到其规定性能。8.7服务如需服务和协助，请联系供应商。尺寸型号。周边装饰指定长度MGT 3010两件式周边装饰指定长MGT 3011（带电缆干线）单元装饰指定长MG T 3020保护导线导管指定长MGG 3030 Mat控制单元MGCP1 MGCS1 MGCD1 MGCSM1与MGCD1系统备件套件描述零件号2保险丝500mA（T）TR5 4对接拼接连接器传感器垫1000mm x 1250mm MGM2025传感器垫1000mm x 1500mm MGM 2030 40长度目录号。标准周边饰件2M 440F-T3210标准周边饰件3M 440F-T3310标准周边内饰5M 440F-T3510外角标准周边饰件440F-T3012内角标准周边内饰440F-T3013带电缆通道2M 440F-13211带电缆通道4M 440F-T3411外角周边饰件
A single fault in any wiring channel will cause the mat control unit to lock the safety output until the fault is corrected and the control unit is reset. Check whether all connecting wires in the system are correctly configured and undamaged, and whether the two contactors work normally. Eliminate all faults. If it is in the manual reset mode, press and release the control unit reset button. 4. If the problem is not solved, please contact the supplier. 38 8.5.2 Symptoms - The machine cannot be stopped or can be started on the mat. Machine 1 is not allowed. If there is a machine on the mat, does the machine enable LED on the mat control unit illuminate? 2. If the MACHINE ENABLED LED is not lit, the machine or its control system may have a fault outside the cushion system. – Do not use the machine until the problem has been corrected and tested. 3. If the machine enable LED lights up- Do not use the machine and contact the supplier immediately. 8.5.3 Symptoms - The machine stops unexpectedly when the sensor pad is not present, but can be restarted after the pad is depressed (and reset in manual reset mode). 1. Check whether all indicators work normally. If so, the problem is likely to be caused by a drop in power supply for a certain value and duration. This may cause an internal relay in the control unit to open, simulating a fault condition. This is a highly unlikely situation and does not require remedial measures. In abnormal situations where the problem persists, measures may need to be taken to ensure a smoother power supply to the mat subsystem. 8.6 Before maintenance works on the cushion system or machine control system, isolate the power supply of the machine and the cushion system.
Observe electrical safety precautions. User repair is limited to replacing new gasket system components. In case of problems, the unit shall be returned to the supplier. Any repairs to the connecting wires shall be made using the recommended butt splice joints. Tampering parts will void the warranty. If the quality seal on the DIN rail control unit is damaged, the warranty is invalid. 39 Spare Parts Available For special size sensor pads, refer to the model number printed on the label. After any part is replaced, the inspection and test as shown in 8.2 must be carried out, and special attention must be paid to the replaced parts. WARNING: All trim, fasteners, and cable protectors must be properly reinstalled after maintenance or repair operations. Failure to do so or the use of unapproved parts or modifications may result in the mat subsystem not achieving its specified performance. 8.7 Service If you need service and assistance, please contact the supplier. Size and model. Specified length of peripheral decoration MGT 3010 two-piece peripheral decoration Specified length MGT 3011 (with cable trunk) Unit decoration Specified length MG T 3020 Protective conductor conduit Specified length MGG 3030 Mat Control unit MGCP1 MGCS1 MGCD1 MGCSM1 and MGCD1 System spare parts kit Description Part No. 2 Fuse 500mA (T) TR5 4 Butt splice connector Sensor pad 1000mm x 1250mm MGM2025 Sensor pad 1000mm x 1500mm MGM 2030 40 Length Catalog No. Standard Perimeter Trim 2M 440F-T3210 Standard Perimeter Trim 3M 440F-T3310 Standard Perimeter Trim 5M 440F-T3510 Exterior Corner Standard Perimeter Trim 440F-T3012 Interior Corner Standard Perimeter Trim 440F-T3013 With Cable Channel 2M 440F-13211 With Cable Channel 4M 440F-T3411 Exterior Corner Perimeter Trim
