MVME172PA-644LE工控DCS系统备件
连续流动的电源和制动电缆符合RoHS和NFPA-79托盘额定值，由UL认证的散装电缆组成。护套颜色符合DESINA规范。电机附件轴封套件适用于MP系列低惯量电机的所有框架尺寸。如果安装正确，密封件在轴上的防护等级为IP66。注意，轴封是需要定期更换的易损件。请参阅《运动控制选择指南》，为您的特定电机选择轴封套件。大多数MP系列电机可使用电机端连接器套件。客户选择自己制造电缆时使用这些电缆。该套件采用金属后壳，压缩式密封电缆护套，并根据套件采用焊接式或压接式连接器插座。罗克韦尔自动化公司为压接式插座提供压接工具。有关更多信息，请访问我们的网站www.ab.com/motion或Kinetix选择指南GMC-SG001x。Allen-Bradley和Kinetix是罗克韦尔自动化的注册商标。
SERCOS接口是德国斯图加特Interest Group SERCOS interface e.V的商标。电缆可用于MP系列电机和其他Allen-Bradley电机以及带有DIN型连接器的致动器。MatGuard压敏安全垫系统安装和用户手册安装前请完整阅读本手册安装后，应将本手册保存在安全、易接近的地方R 1 2 MatGuard-压敏安全垫安装和使用手册第1节存储和搬运第4页第2节系统说明第5页第3节应用第8页第4节规范第10页第5节安装设计第14页第6节安装和调试第26页第7节使用第36页第8节维护第37页传感器垫标记本手册参考了以下标准：EN 292-1和2：机械安全-基本概念-一般设计原则-第1和2部分EN 294：机械安全–防止的安全距离上肢触及的危险区域。EN 811：机械安全-防止下肢触及危险区域的安全距离。
Continuous flow power and brake cables comply with RoHS and NFPA-79 tray ratings and consist of UL certified bulk cables. Sheath color shall conform to DESINA specification. The motor accessory shaft seal kit is applicable to all frame dimensions of MP series low inertia motors. If installed correctly, the protection class of the seal on the shaft is IP66. Note that the shaft seal is a wearing part that needs to be replaced regularly. Refer to the Motion Control Selection Guide to select a shaft seal kit for your specific motor. The motor end connector kit is available for most MP series motors. These cables are used when customers choose to make their own cables. The kit uses a metal back shell, a compression sealed cable sheath, and a welded or crimped connector socket according to the kit. Rockwell Automation provides crimping tools for crimping sockets. For more information, please visit our website at www.ab.com/motion or Kinetix Selection Guide GMC-SG001x. Allen Bradley and Kinetix are registered trademarks of Rockwell Automation.
SERCOS interface is a trademark of the Interest Group SERCOS interface e.V in Stuttgart, Germany. Cables can be used for MP series motors and other Allen Bradley motors as well as actuators with DIN type connectors. Please read this manual completely before installing the MatGuard pressure-sensitive safety pad system and the user manual. After installation, this manual should be kept in a safe Accessible places R 1 2 MatGuard Pressure Sensitive Safety Pad Installation and Use Manual Section 1 Storage and Handling Page 4 Section 2 System Description Page 5 Section 3 Application Page 8 Section 4 Specifications Page 10 Installation Design Page 14 Section 6 Installation and Commissioning Page 26 Section 7 Use Page 36 Section 8 Maintenance Page 37 Sensor Pad Marking This manual refers to the following standards: EN 292-1 and 2: Mechanical Safety - Basic Concepts - General Design Principles - Part 1 and 2 EN 294: Safety of machinery – safe distance to prevent danger areas touched by upper limbs. EN 811: Safety of machinery - Safety distances to prevent lower limbs from reaching hazardous areas.
