MVME197备件模块
停止“红色”LED亮起。c） 安全触点打开。d） 辅助触点闭合。e） 接触器断电。4） 释放配置文件a）停止“红色”LED熄灭。b） 系统已返回到步骤1a。5） 如果在重置前按下配置文件，a）每次按下配置文件时，停止“红色”LED将点亮，但安全触点不会通电。440F-C251P表面安装440F-C2514D DIN导轨继电器输出：2 x独立无电压N/O安全触点1 x无电压N/C辅助触点注意：辅助触点不应用于安全用途类别：AC-15；2A/250V直流-13；2A/30V DC安全输入：安全曲线（开路电阻6KΩ ) 指示LED 1：绿色：运行。LED 2：黄色：打开。LED 3：红色：停止。内部控制：交流电压选择器内部保险丝：2A安全保险丝可更换（2个）500mAT电源保险丝可更换。环境温度范围-剖面-5°C至+55°C，不包括110N和01610N（0°C至55°C）湿度：+55°C.时相对湿度高达90%。振动：根据IEC 68-2-6进行测试，频率范围10-55Hz，位移0.15mm，每轴10个周期，扫描速率，每分钟1个八度，MC-MC接触器监控回路：N/C（常闭）接触器回路最大导线尺寸：1 x 1 mm 2绞合，套管剥离1x2.5 mm 2绞合套管剥离5mm，1 x 1.5mm 2实心导线。8mm，1 x 4 mm 2实心导体端子：负端子螺钉+负端子螺钉M3.5，M2弹簧作用。自举连接，垫圈端子板可单独拆卸。安装组：符合VDE 0110的C。材料：聚碳酸酯固定细节：4 x M4孔35 mm DIN导轨外壳：D=75mm，H=130mm，W=130mm D=120mm，H=73mm，W=45.5mm，16路重量：650g 450g
其他：安全型材必须以6K终止Ω 电阻器。11 16 440F-E0110N 440F-E0110 s 440F-E0310S 440F-E1610N 440F-E1610 s致动距离：6.4mm 6.6mm 8.0mm 7.8mm 9.4mm响应距离：1.2mm 1.9mm 27.2mm 8.4mm 5.0mm•最大速度：100 mm/s•适合检测手指控制单元不得安装在危险区内。手动复位或常规指示器观察需要接近控制单元，因此必须能够看到其运行。控制单元可以安装在电动门的任何一侧，只要唯一的危险是实际的门。在所有其他情况下，考虑到测试和维护的访问要求，控制单元可以安装在危险区外任何方便的地方。3.3.2安装440F-C251P（表面安装）440F-C2514D（Din导轨安装）35MM Din导轨安装45.5 73 120 A1+Z2 MC 13 23 31 A2-Z1 MC 14 24 32 115mm 130mm 115mm 4 x M4固定孔Pg16/21 Pg16/21 75mm 4.6复位端子MC-MC这些端子用于多种不同功能（表面安装提供跳线，Din导轨提供无跳线）。在没有跳线的情况下，端子可以连接到机器接触器上的正向引导常闭辅助触点，以监控双通道控制系统中的接触器。如果一个接触器在其控制线圈断电时未能隔离电源，则Safedge系统将不允许另一个接触器通电，直到故障得到纠正。如果不需要此功能，请在DIN导轨装置的这些端子之间安装跳线。此端子也用于自动/手动复位。如果MC-MC端子未跨接或仅连接至接触器常闭触点，则装置处于自动复位模式。在自动复位模式下，仅通过移除驱动力来实现输出。在致动器通电时（当不存在驱动力时）也可以实现输出。
The stop "red" LED lights up. c) Safety contacts open. d) The auxiliary contacts are closed. e) The contactor is de energized. 4) Release the profile a) Stop The "red" LED goes off. b) The system has returned to step 1a. 5) If the profile is pressed before reset, a) the stop "red" LED will illuminate each time the profile is pressed, but the safety contacts will not be energized. 440F-C251P surface mount 440F-C2514D DIN rail relay output: 2 x independent voltage free N/O safety contact 1 x voltage free N/C auxiliary contact Note: auxiliary contact shall not be used for safety purpose Category: AC-15; 2A/250V DC - 13; 2A/30V DC safety input: safety curve (open circuit resistance 6K Ω) indicating LED 1: green: running. LED 2: yellow: on. LED 3: red: stop. Internal control: AC voltage selector Internal fuse: 2A safety fuse replaceable (2) 500mAT power fuse replaceable. Ambient temperature range - profile - 5 ° C to+55 ° C, excluding 110N and 01610N (0 ° C to 55 ° C) Humidity:+55 ° C The relative humidity is up to 90%. Vibration: tested according to IEC 68-2-6, with frequency range of 10-55Hz, displacement of 0.15 mm, 10 cycles per axle, scanning rate of 1 octave per minute, MC-MC contactor monitoring circuit: N/C (normally closed) contactor circuit, maximum conductor size: 1 x 1 mm 2 stranded, casing stripping 1x2.5 mm 2 stranded, casing stripping 5 mm, 1 x 1.5 mm 2 solid conductor. 8mm, 1 x 4 mm2 solid conductor terminal: negative terminal screw+negative terminal screw M3.5, M2 spring action. Bootstrap connection, gasket terminal board can be disassembled separately. Installation group: C according to VDE 0110. Material: polycarbonate fixing details: 4 x M4 hole 35 mm DIN rail housing: D=75mm, H=130mm, W=130mm D=120mm, H=73mm, W=45.5mm, 16 circuit weight: 650g 450g
Others: The safety profile must terminate the Ω resistor with 6K. 11 16 440F-E0110N 440F-E0110 s 440F-E0310S 440F-E1610N 440F-E1610 s Actuation distance: 6.4mm 6.6mm 8.0mm 7.8mm 9.4mm Response distance: 1.2mm 1.9mm 27.2mm 8.4mm 5.0mm • Maximum speed: 100 mm/s • Suitable for finger detection Control unit shall not be installed in hazardous area. Manual reset or conventional indicator observation requires access to the control unit, so it must be possible to see its operation. The control unit can be installed on either side of the electric door, as long as the only danger is the actual door. In all other cases, considering the access requirements for testing and maintenance, the control unit can be installed at any convenient place outside the hazardous area. 3.3.2 Install 440F-C251P (surface mount) 440F-C2514D (Din rail mount) 35MM Din rail mount 45.5 73 120 A1+Z2 MC 13 31 A2-Z1 MC 14 24 32 115mm 130mm 115mm 4 x M4 fixing hole Pg16/21 Pg16/21 75mm 4.6 reset terminal MC-MC These terminals are used for a variety of different functions (surface mount provides jumper, Din rail provides no jumper). Without jumpers, the terminals can be connected to the positive pilot normally closed auxiliary contacts on the machine contactors to monitor the contactors in the dual channel control system. If a contactor fails to isolate power when its control coil is de energized, the Safedge system will not allow another contactor to be energized until the fault is corrected. If this function is not required, install jumpers between these terminals of the DIN rail unit. This terminal is also used for automatic/manual reset. If the MC-MC terminal is not jumpered or only connected to the normally closed contact of the contactor, the device is in automatic reset mode. In the automatic reset mode, the output is achieved only by removing the driving force. The output can also be achieved when the actuator is energized (when there is no driving force).
