MVME197DP机械设备卡件
在阴影区域的其余部分涂上粘合剂，使密封唇与型材接触。重要事项：将粘合剂均匀涂抹在阴影区域！不要让粘合剂进入型材内部。5.3应用Z1 Z2+-棕白色L 6K 电阻器停止启动110/230V交流电源110/230V AC应用，带2个接触器、接触器监控和启动/停止电路。（显示为按下轮廓）瞬时按钮外部保险丝+ve Z1 Z2 13 23 31 N E-ve MC 14 24 32安全轮廓安全控制单元K1 K1 K2 K2 K1 K2（A1）（A2）L 6K 电阻器K1外部保险丝110/230V AC应用，带1个接触器。（显示为按下轮廓）+ve Z1 Z2 13 23 31 N E-ve MC 14 24 32安全轮廓安全控制单元（A2）（A1）9 18 3.2.9为确保完全密封，在索环/电缆出口和封口盖密封唇周围的安全轮廓上涂抹更多粘合剂。3.2.10轴向型材连接器440F-A0061S仅用于440F-E0110系列型材的延伸和维修（参见步骤1、2、3、6和7）。对于其他类型，请使用直销连接器。3.3控制单元3.3.1技术规范440F-C251P表面安装440F-C2514D DIN导轨符合性：prEN 1760-2，EN 954-1：3类电源-用户选择：110/230V AC（50-60Hz）和24V AC/DC+10%-15%系统响应时间：13mS环境保护：IP65。外壳IP40 DIN0470端子IP20 DIN0470最大安全轮廓电压：12V DC（开路）。
标称工作电压：4V（运行条件）。最大输出保险丝：2A快动5A快动冲击耐受电压：2500V。过电压：2类污染等级：III最小开关电流/电压：10mA/10V功耗：<6 VA 10 5.2自动复位模式1）打开电源a）运行“绿色”LED亮起。b） 安全触点闭合。c） 辅助触点断开。d） 接触器通电。2） 按下配置文件a）运行“绿色”LED熄灭。b） 停止“红色”LED亮起。c） 安全触点打开。d） 辅助触点闭合。e） 接触器断电。3） 释放配置文件a）系统已返回步骤1a。对比性能型材440F-E0110N 440F-E0110 S 440F-E0110.R 440F-E0510S 440F-E1610N 440F-E1610 S 440F-E804 S 440F--E0310S 440F-E0210S拉伸强度（增强）MPa 26 20弹性（20°C）F G低温柔韧性F G耐阳光G G耐热老化G G耐氧化F G耐臭氧F G耐H2O G G耐稀释酸F G耐浓酸F G抗油和油脂G P键：-G=良好F=一般P=较差17接线端子紧固扭矩额定值7英寸/磅，440F-A0061S适用于16AWG电线尺寸。至少使用16AWG。仅使用铜导线。现场接线的温度额定值不得低于环境温度。5.0调试和使用操作顺序装置安装后，检查以下操作顺序。5.1手动复位模式。1） 打开电源a）没有LED亮起。2） 按下重置开关a）运行“绿色”LED亮起。b） 安全触点闭合。c） 辅助触点断开。d） 接触器通电。3） 按下配置文件a）运行“绿色”LED熄灭。b）
Apply adhesive to the rest of the shaded area so that the sealing lip contacts the profile. IMPORTANT: Apply the adhesive evenly to the shaded area! Do not allow the adhesive to enter the inside of the profile. 5.3 Use Z1 Z2+- brown white L 6K resistor to stop starting 110/230V AC power supply 110/230V AC application, with 2 contactors, contactor monitoring and start/stop circuit. (Displayed as pressing contour) Momentary button external fuse+ve Z1 Z2 13 23 31 N E-ve MC 14 24 32 Safety contour safety control unit K1 K1 K2 K2 K1 K2 (A1) (A2) L 6K resistor K1 External fuse 110/230V AC application, with 1 contactor. (Shown as pressed contour)+ve Z1 Z2 13 23 31 N E-ve MC 14 24 32 Safety contour Safety control unit (A2) (A1) 9 18 3.2.9 To ensure complete sealing, apply more adhesive to the safety contour around the grommet/cable outlet and the sealing lip of the closure cap. 3.2.10 The axial profile connector 440F-A0061S is only used for the extension and maintenance of 440F-E0110 series profiles (see steps 1, 2, 3, 6 and 7). For other types, use straight pin connectors. 3.3 Control unit 3.3.1 Technical specification 440F-C251P Surface mounting 440F-C2514D DIN rail compliance: prEN 1760-2, EN 954-1: Class 3 power supply - user selection: 110/230V AC (50-60Hz) and 24V AC/DC+10% - 15% System response time: 13mS Environmental protection: IP65. Enclosure IP40 DIN0470 terminal IP20 DIN0470 maximum safe contour voltage: 12V DC (open circuit).
Nominal working voltage: 4V (operating conditions). Maximum output fuse: 2A fast acting 5A fast acting impulse withstand voltage: 2500V. Overvoltage: Class 2 pollution level: III Minimum switching current/voltage: 10mA/10V Power consumption:<6 VA 10 5.2 Automatic reset mode 1) Turn on the power a) Run the "green" LED on. b) The safety contact is closed. c) The auxiliary contact is open. d) The contactor is energized. 2) Press profile a) Run "green" LED turns off. b) The stop "red" LED lights up. c) Safety contacts open. d) The auxiliary contacts are closed. e) The contactor is de energized. 3) Release the configuration file a) The system has returned to step 1a. Comparison of performance profiles 440F-E0110N 440F-E0110 S 440F-E0110. R 440F-E0510S 440F-E1610N 440F-E1610 S 440F-E804 S 440F-E0310S 440F-E0210S 440F-E0210S Tensile strength (enhanced) MPa 26 20 Elasticity (20 ° C) F G Low temperature flexibility F G Sunshine resistance G Heat aging resistance G G Oxidation resistance F G Ozone resistance F G H2O resistance G Diluted acid resistance F G Concentrated acid resistance F G Oil resistance and grease G P key: - G=Good F=General P=Poor 17 Rated tightening torque of terminal 7 inches/pound, 440F-A0061S is applicable to 16AWG wire size. Use at least 16AWG. Use only copper conductors. The temperature rating of the field wiring shall not be lower than the ambient temperature. 5.0 After commissioning and using the operation sequence device, check the following operation sequence. 5.1 Manual reset mode. 1) Turn on the power a) No LED is lit. 2) Press the reset switch a) Run "green" LED lights up. b) The safety contact is closed. c) The auxiliary contact is open. d) The contactor is energized. 3) Press profile a) Run "green" LED turns off. b）
