MVME224A-3工控备件模块
无捻或无捻的连续纱线、丝束或纤维的平行粗纱束。饱和树脂（或饱和剂）-聚合物基树脂，用于浸渍增强纤维，将其固定到位，并在纤维之间传递负载。包装材料的保质期可以在特定条件下储存并保持可用。对长丝进行上浆表面处理，以赋予所需的加工、耐久性和粘合性能。在动态力学分析期间，在经历循环变形的粘弹性材料中存储能量的存储模量测量。两束无捻的连续长丝。乙烯基酯树脂环氧树脂与可聚合不饱和酸的热固性反应产物（通常为1 6 2 8 4 9 5 7 12 3 11 I/O端口21.5英寸和24英寸显示器尺寸10安全压敏安全边缘系统安装和用户手册安装前请阅读本手册安装后，应将本手册保存在安全、易接近的地方R图纸编号：31611第2期R EO:26630 Guardmaster安全压敏安全边系统安装和用户手册第1节存储和搬运第2节系统说明第3节安装和规范第4节电气连接第5节调试和使用第6节维护和服务表面安装DIN导轨安装安全EN 954-1目录 STOP OPEN安全压敏安全边缘系统控制单元电源电压230/110VAC（见选择器）50-60Hz 0r 24V AC/DC IP65防水，防尘安全触点250V 2A N/O辅助触点250V 2AN/C安全轮廓电压12Vdc EN 954-1类别3
prEN 1760-2系统响应时间13mS更多信息请参阅用户手册，在打开R压敏边缘系统控制单元Pt之前隔离电源。编号440F-C251P英国制造全面检查和测试记录（见第6.2.2节和6.2.3节）意见检查日期1 26 25 2常规检查和测试的记录（见6.2.2节和第6.2.3节）注释检查日期简介Safedge灵敏边缘传感系统是电动门等应用中的理想安全传感器，自动车辆和移动机械床等。它可以提供沿着或围绕几乎任何物体的连续的高灵敏度触摸感应线。本手册涵盖Safedge系统部件的使用。如果需要接头或拐角，请联系供应商。所有安装工作必须由经过适当培训的合格人员进行，并应符合法定安全要求。安装前请完整阅读本手册。安装后，应将本手册保存在安全且可接近的地方。如需进一步帮助，请联系您的供应商。1.0储存和搬运储存安全控制装置和配置文件应储存在-10°C至+55°C的温度范围内。搬运和运输安全控制装置和型材应在-10°C至+55°C的温度范围内运输，不得受到任何冲击或重载。应使用原始包装，以防止过度弯曲。务必小心打开包装，避免使用刀具等造成损坏。2.0系统描述安全系统由长达50米的型材、电缆连接器、终端电阻器、“C”型导轨和控制单元组成。
A parallel roving bundle of twistless or untwisted continuous yarn, tow, or fiber. Saturated resin (or saturant) - a polymer based resin used to impregnate reinforcing fibers, hold them in place, and transfer loads between fibers. The shelf life of packaging materials can be stored under specific conditions and kept available. Sizing surface treatment of the filament to give the required processing, durability and adhesion properties. Storage modulus measurement of stored energy in viscoelastic materials undergoing cyclic deformation during dynamic mechanical analysis. Two strands of untwisted continuous filament. Thermosetting reaction products of vinyl ester resin epoxy resin and polymerizable unsaturated acid (Usually 1 6 2 8 4 9 5 7 12 3 11 I/O ports 21.5 inch and 24 inch display size 10 Safety pressure-sensitive safety edge system Please read this manual before installation and user manual After installation, this manual should be kept in a safe and accessible place R Drawing No.: 31611 Phase 2 R EO: 26630 Guardmaster Safety pressure-sensitive safety edge system Installation and user manual Section 1 Storage and handling Section 2 System description Section 3 Installation and specifications Section 4 Electrical Connection Section 5 Commissioning and Use Section 6 Maintenance and Service Surface Mounting DIN Rail Mounting Safety EN 954-1 Table of Contents STOP OPEN Safety Pressure Sensitive Safety Edge System Control Unit Power Supply Voltage 230/110VAC (see selector) 50-60Hz 0r 24V AC/DC IP65 Waterproof and dust-proof safety contact 250V 2A N/O Auxiliary contact 250V 2AN/C Safety profile voltage 12Vdc EN 954-1 Category 3
PrEN 1760-2 System response time 13mS For more information, please refer to the user manual and isolate the power supply before turning on the R voltage sensitive edge system control unit Pt. No. 440F-C251P British Manufacturing Overall Inspection and Test Record (see Sections 6.2.2 and 6.2.3) Opinion Inspection Date 1 26 25 2 Record of Routine Inspection and Test (see Sections 6.2.2 and 6.2.3) Note Inspection Date Introduction Safedge Sensitive Edge Sensing System is an ideal safety sensor for applications such as electric doors, automatic vehicles and mobile mechanical beds. It can provide continuous high-sensitivity touch sensing lines along or around almost any object. This manual covers the use of Safedge system components. If joints or corners are required, contact the supplier. All installation work must be carried out by suitably trained and qualified personnel, and shall comply with statutory safety requirements. Please read this manual completely before installation. After installation, keep this manual in a safe and accessible place. For further assistance, please contact your supplier. 1.0 Storage and Handling Storage Security Controls and Profiles shall be stored in a temperature range of - 10 ° C to+55 ° C. The handling and transportation safety control devices and profiles shall be transported within the temperature range of - 10 ° C to+55 ° C without any impact or heavy load. The original packaging shall be used to prevent excessive bending. Be sure to open the package carefully to avoid damage caused by using knives, etc. 2.0 System Description The safety system consists of 50 meter long profiles, cable connectors, termination resistors, "C" type rails and control units.
