MVME332XTP库存备件
查看驱动器状态查看参数和信号浏览树窗格项目集窗格3.备件处理我们建议您为驱动器控制板备件保留每个DDCS通信通道中的一个节点地址。原因是：•用作备件的控制板在装运时通常有一个预先编程的节点地址。•如果控制板完全没有编程，它将在节点地址1处启动。•如果节点地址1处有驱动器，则DriveWindow中需要或能够重新启动驱动器的功能无法在其他节点重新启动驱动器。原因是，任何重新启动的驱动器都会使用一个节点地址，并且在此期间会有两个驱动器在同一节点地址处响应。如果不遵循这些建议，则无法：•下载其他驱动器的参数后重新启动。•将系统软件还原或下载到其他驱动器。如果您遵循建议并将节点地址保留为一个备用地址，例如，用备用地址替换控制板是很容易的。调试完成后，对所有驱动器进行完全备份。您可以将它们全部保存在一个备份包文件中。如果驱动器的控制板出现故障，需要用备件更换：•用备件更换控制板。您不需要关闭其他驱动器的电源。•如果DriveWindow正在运行，请断开OPC服务器或退出。•给驱动器通电。•启动DriveWindow和/或连接OPC服务器。修复的驱动器应出现在节点地址1。•打开备份包文件。•选择要恢复的节点地址1处的已修复驱动器。•从备份包中选择要用于恢复的原始节点。•执行还原。如果一切正常，修复后的驱动器将显示在其原始节点地址。•通过关闭备份包进行清理。请注意，如果使用这种处理备件的方法，则无需在光学DDCS网络中进行任何连接更改。其他DriveWindow 2 9-31另请参阅：什么是备份包如何备份如何恢复如何恢复参数4.限制4.1.1最大板数DriveWindow本身不使用通信板本身。因此，限制由DriveOPC设置，DriveWindow使用DriveOPC与驱动器通信。从2.03版（包括在DriveWindow 2.02版中）开始，DriveOPC可以处理多个DDCS通信板。支持的板的数量取决于操作系统。自2.08版（包括在DriveWindow 2.22版中）起，DriveOPC还可以在Windows 2000/XP/Vista下处理RUSB-02 USB/DDS适配器。尽管DriveOPC 2.09版（包括在DriveWindow 2.30版中）支持，但DriveWindow 2.33（或更高版本）安装不支持NISA-03板和Windows NT。
See Also: Viewing Status of Drives Viewing Parameters and Signals Browse Tree Pane Item Sets Pane 3. Handling of Spare Parts We recommend that you reserve the node address one of each DDCS communication channel for drive control board spare parts. The reasons are: • Control boards made to be used as spare parts have usually node address one preprogrammed, when they are shipped. • If a control board has not been programmed at all, it boots at node address one. • Functions within DriveWindow, which require or are able to restart a drive, cannot do restarting of drives at other nodes, if there is a drive at node address one. The reason is that any restarting drive uses node address one for while, and there would be two drives responding at the same node address during that time. If you do not follow these recommendations, you are not able to: • Restart other drives after downloading their parameters. • Restore or download system software to other drives. If you follow the recommendations and leave the node address one free for spare parts, replacing a control board, for example, with a spare is easy. After commissioning is done, take full backup of all drives. You can have them all in a single backup package file. If a control board of a drive fails and needs to be replaced by a spare: • Replace the control board with a spare. You do not need power off other drives. • If you have DriveWindow running, either disconnect the OPC Server or exit. • Power up the drive. • Start DriveWindow and/or connect the OPC Server. The repaired drive should appear at node address one. • Open the backup package file. • Select the repaired drive at node address one to be restored. • Select the original node from the backup package to be used in restoring. • Execute restoring. If all went well, the repaired drive will be shown at its original node address. • Clean up by closing the backup package. Note that you do not need to do any connection changes in the optical DDCS network, if using this method of handling spare parts. Miscellaneous DriveWindow 2 9-31 See Also: What is a Backup Package How to Backup How to Restore How to Restore Parameters 4. Limitations 4.1.1 Maximum Number of Boards DriveWindow itself does not use the communication boards itself. So, the limits are set by the DriveOPC, which DriveWindow uses in communication with the drives. Since version 2.03 (included in DriveWindow version 2.02), DriveOPC can handle several DDCS communication boards. Number of supported boards depends on the operating system. Since version 2.08 (included in DriveWindow version 2.22), DriveOPC can handle also RUSB-02 USB/DDCS adapters under Windows 2000/XP/Vista. Although supported by DriveOPC version 2.09 (included in DriveWindow version 2.30), DriveWindow 2.30 (or newer) installation does not support NISA-03 boards and Windows NT.
