MVME3604-5131B工控备件模块
这意味着仅使用SAP/http以太网通信。•禁用端口是一个逗号分隔的COM端口号或不用于SAP通信的编号范围列表。范围-n表示0-n，n-表示n-4294967295。OPC服务器7-68 DriveWindow 2搜索设备组该组定义了在连接时是否使用广播方法搜索SAP/http设备。通常情况下，您不会同时使用这两种方法。该组包含：•近表示使用本地以太网段UDP广播（IP=255.255.255.255，RFC 919）。•Intranet表示使用PC子网UDP广播（IP=IP或非子网掩码，RFC 922）。请注意，如果PC属于多个子网，则会广播所有子网。设备组该组定义SAP/http设备的IP地址（固定IP）。指定的频道号不能重叠。具有重叠信道号的设备规范在连接时被忽略。OPC服务器DriveWindow 2 7-69注意，所有DriveOPC设备（如果有的话）的信道号都在本地DriveDA信道的最后一个信道号之后移动。该组包含：•IP地址定义IP地址（固定IP）。•“状态”组中的“否检查”指定在启动时不查询设备的状态。尽管这可能会加快启动速度，但大多数通信属性不可用。•“状态”组中的“无论如何使用”指定在启动时查询设备的状态，但如果设备没有响应，则无论如何使用。如果设备不响应状态查询，则大多数通信属性不可用。•频道号可以为固定IP指定固定的频道号。负值（-1）表示自动编号（Auto）。协议组该组包含NETA-21特定设置。请注意，如果两个NETA-21面板总线都在使用，则设备在固定IP列表中显示两次，并附加/1和/2。但是，如果Find用于添加IP地址，则只显示一次，但没有附加总线号。没有附加总线号的NETA-21实际上意味着两个通道，即两条总线都在使用。还要注意，如果两个NETA-21面板总线都在使用，则不能为设备指定固定的通道号。如果要做到这一点，应两次指定相同的设备IP，每个面板总线一个。该组包含：•NETA指定SAP/http设备是否为NETA-21。•NETA通道指定使用NETA-21的哪个面板总线。这两种方法都可以使用。另请参阅：使用DriveDA DriveWindow 2配置SAP/http连接到OPC服务器8-1第8章-系统软件内容系统软件8-2 DriveWindow 2另请参阅系统软件子菜单1.定义•系统软件•备份包•加载包1.1什么是系统软件系统软件由保存在AMC板闪存prom中的所有持久“文件”组成，排除引导程序。通常，系统软件文件可分为：•操作系统和电机控制器文件•面板处理文件
It means that only SAP/http Ethernet communication is used. • Disable Ports is a comma separated list of COM port numbers or number ranges which are not used for SAP communication. A range -n means 0-n and n- means n-4294967295. OPC Server 7-68 DriveWindow 2 Search Devices group The group defines, whether the broadcast methods are used to search SAP/http devices at connection time or not. Typically you never use both of them. The group contains: • Near means that local Ethernet segment UDP broadcast (IP=255.255.255.255, RFC 919) is used. • Intranet means that the PC subnet UDP broadcast (IP=IP or not subnet mask, RFC 922) is used. Note that if the PC belongs to several subnets, all of them are broadcasted. Device group The group defines the IP address (Fixed IP) of a SAP/http device. Channel Numbers specified must not overlap. A device specification having an overlapping Channel Number is disregarded at connection time. OPC Server DriveWindow 2 7-69 Note that the channel numbers of all DriveOPC devices (if any) are shifted after the last channel number of the native DriveDA channels. The group contains: • IP Address defines the IP address (Fixed IP). • No Check in the Presence group specifies that the presence of the device is not queried at start-up. Although it may speed up the start-up, most of the Communication Properties is not available. • Use Anyway in the Presence group specifies that the presence of the device is queried at start-up but, if it does not respond, it is used anyway. If the device does not respond to presence queries, most of the Communication Properties is not available. • Channel Number can specify a fixed channel number for a Fixed IP. Negative value (-1) means automatic numbering (Auto). Protocol group The group contains NETA-21 specific settings. Note that if both NETA-21 panel buses are in use, the device is either shown twice in Fixed IPs list with /1 and /2 appended. However, if Find is used for adding IP addresses, it is shown just once but without an appended bus number. A NETA-21 without an appended bus number means actually two channels, .i.e., both buses are in use. Note also that if both NETA-21 panel buses are in use, you cannot specify a fixed Channel Number for the device. If you want to do that, you should specify the same device IP twice, one for each of the panel buses. The group contains: • NETA specifies, whether the SAP/http device is NETA-21 or not. • NETA Channels specifies which of the panel buses of the NETA-21 is used. Also both of them can be used. See Also: Configuring SAP/http Connecting to OPC Server Using DriveDA DriveWindow 2 8-1 Chapter 8 - System Software Contents System Software 8-2 DriveWindow 2 See Also: System Software Submenu 1. Definitions • System Software • Backup Package • Loading Package 1.1 What is System Software System Software consists of all the persistent "files" that are saved in the flash prom of the AMC board, the boot program excluded. Typically System Software files can be divided into: • Operating System and Motor Controller files • Panel Handling file
