MVME3604-6342机器人备件
右键单击对话框中的“固定IP”列表将显示上下文菜单。或者请注意，您也可以通过点击Del键来删除所选的固定IP。还请注意，如果“固定IP”列表中没有条目或未选择条目，则菜单中除“新建”以外的所有其他命令都将灰显。8.1.9通过查找设备添加和删除固定IP请注意，查找操作仅在UDP端口24576空闲且未被防火墙阻止时有效。要查找靠近或intranet设备的SAP/http设备的IP地址，请单击配置设置对话框的查找组中的靠近设备或intranet设备按钮。将显示OPC服务器7-54 DriveWindow 2找到的设备对话框。在左侧，您可以看到所选当前配置中未包含的SAP/http设备列表。在右侧，您可以看到所选当前配置中包含的SAP/http设备列表。请注意，所选当前配置中未找到的SAP/http设备不会显示在两个列表中。所以你只能在这里操纵找到的设备。OPC服务器驱动窗口2 7-55现在您可以：•通过单击>>按钮添加所有找到的尚未包含的设备•通过单击按钮删除所有找到的当前包含的设备。•通过在“包含”列表中单击（按住Ctrl键或Shift键）并单击>按钮来选择当前包含的选定设备，从而删除这些设备。例如：OPC服务器7-56 DriveWindow 2最后单击“确定”返回配置设置对话框。OPC服务器驱动窗口2 7-57现在可以在固定IP列表中看到更改。请注意，如果添加了新的NETA-21，则其RS-485总线都包含在内，并且固定IP列表中未显示通道。当DriveDA连接时，DriveDA会自动连接到两条总线，即保留两个通道。8.1.10典型工作流程当您来到一个以太网段中有SAP/http设备的站点时，您的工作流程可能如这里所述。注意，在连接到DriveDA OPC服务器之前，不必启用NETA-21面板网关。第一件事是打开SAP/http设备，等待3-5分钟，使其启动并运行。然后启动DriveWindow，但不要连接到OPC服务器。从网络菜单的配置子菜单中选择SAP/http。OPC服务器7-58 DriveWindow 2从SAP/http配置对话框的编辑菜单中选择新建。输入可以轻松与站点关联的新配置的名称，然后单击“确定”。OPC服务器驱动窗口2 7-59在“新配置的设置”对话框中启用SAP/http通信。使此配置中的所有或许多SAP/http设备共用其他设置更改。
of the dialog box for Settings of a configuration and in the context menu, which is displayed if you right click the Fixed IPs listing in the dialog box. or Note that you can delete the selected Fixed IP also by hitting the Del key. Note also that if there is no entry in the Fixed IPs list or no entry is selected, all other commands than New are grayed in the menu. 8.1.9 Adding and Deleting Fixed IPs by Finding Devices Note that the Find operation works only if the UDP port 24576 is free and not blocked by the firewall. To find IP addresses of SAP/http devices near or intranet devices, click the Near Devices or Intranet Devices button in the Find group of the dialog box for Settings of a configuration. OPC Server 7-54 DriveWindow 2 The Devices Found dialog box is displayed. On the left side you have a list of SAP/http devices found that are not included in the selected Current configuration. On the right side you have a list of SAP/http devices found that are included in the selected Current configuration. Note that a SAP/http device included in the selected Current configuration that is not found is not displayed in either of the lists. So you can manipulate here only the devices found. OPC Server DriveWindow 2 7-55 Now you can: • Add all found devices not yet included by clicking the >> button • Delete all found devices currently included by clicking the button. • Delete selected devices currently included by selecting them by clicking (with Ctrl or Shift key down) in the Include list and then clicking the > button. For example: OPC Server 7-56 DriveWindow 2 Finally click OK to get back to the dialog box for Settings of a configuration. OPC Server DriveWindow 2 7-57 The changes can now be seen in the Fixed IPs list. Note that if a new NETA-21 is added, both of its RS-485 buses are included and the channels are not shown in the Fixed IPs list. When DriveDA connection is made, DriveDA connects automatically to both buses, i.e., two channels are reserved. 8.1.10 Typical Workflow When you come to a site having SAP/http devices in an Ethernet segment, your workflow may be as explained here. Note that until you connect to the DriveDA OPC server, it is not necessary to have the panel gateway of NETA-21 enabled. The first thing is to put the SAP/http devices on and wait 3-5 minutes to get them up and running. Then start DriveWindow, but do not connect to an OPC Server. Select SAP/http from Configure submenu of the Network menu. OPC Server 7-58 DriveWindow 2 Select New from the Edit menu in the SAP/http Configuration dialog box. Enter a name for the new configuration that you can easily associate with the site and click OK. OPC Server DriveWindow 2 7-59 In the Settings for the new configuration dialog box enable SAP/http Communication. Make other setting changes common for all or many of the SAP/http devices in this configuration.
