MVME374-001机械设备卡件
可以编辑所有配置并将其复制到新配置。您可以从“编辑”菜单或右键单击“当前配置”下拉列表时显示的上下文菜单中选择操作。或注意，您也可以通过点击Del键来删除所选的当前配置。配置可以包含以下连接到SAP/http设备的方法的任意组合：•固定IP列表（不在默认配置中）。•附近的设备，即本地以太网段中的所有设备（通过广播搜索）。•Intranet设备，即与PC位于同一子网中的所有设备（通过广播搜索）。此外，您可以配置DriveDA尝试用于RS-485通信的COM端口的使用。在实践中，您只使用只有固定IP的配置。使用广播的其他方法可以用于具有SAP/http设备的训练或其他条件，其IP地址经常改变。OPC服务器驱动窗口2 7-49 8.1.4测试配置要测试选定的当前配置，请单击测试按钮。如果按钮呈灰色，则可能安装了旧版本的DriveDA（实际上是其通信模块）。将显示一个对话框，其中包含所选当前配置找到的COM端口和SAP/http设备的列表。请注意，测试不会检查NETA-21的RS-485网络中是否有驱动器。因此，尽管找到了SAP/http设备，但当DriveWindow连接到DriveDA时，可能找不到驱动器。还要注意，即使其面板网关被禁用，也可以找到NETA-21设备。但是，当DriveWindow连接到DriveDA时，找不到驱动器。如果测试未找到任何COM端口或SAP/http设备，将显示消息框而不是对话框。OPC服务器7-50 DriveWindow 2 8.1.5保存更改要保存对SAP/http配置所做的任何更改，请单击SAP/http配置对话框中的确定按钮。8.1.6编辑配置通常，您很少编辑默认配置。要编辑配置，请首先将其选择为“当前配置”，然后从“编辑”或上下文菜单中选择“属性”。或OPC服务器驱动窗口2 7-51显示配置设置对话框。通常使用默认值，即默认配置中定义的值。一个例外是SAP/http通信可能需要启用，因为它可能在默认情况下被禁用。并非所有设置都显示在对话框中。FixedIP中列出的每个固定IP的设置都显示在单独的对话框中。OPC服务器7-52 DriveWindow 2 8.1.7固定IP设置要编辑固定IP的设置，请在配置设置对话框的固定IP列表中单击该设置，然后从编辑菜单中选择属性命令，或在固定IP列表中右键单击该设置并从显示的上下文菜单中选择“属性”命令。或显示配置的固定IP设置对话框。OPC服务器驱动窗口2 7-53 8.1.8添加和删除固定IP可在“编辑”菜单中找到用于添加或删除固定IP的命令
All configurations can be edited and copied to a new. You can select to operation either from the Edit menu or the context menu, which is shown when you right click Current configuration drop down list. or Note that you can delete the selected Current configuration also by hitting the Del key. A configuration can contain any combination of the following methods of connecting to SAP/http devices: • A list of fixed IPs (not in the Default configuration). • Devices near, i.e., all devices in the local Ethernet segment (searched by broadcast). • Intranet devices, i.e., all devices in the same subnet as the PC (searched by broadcast). In Addition you can configure the use of COM-ports that DriveDA tries to use for RS-485 communication. In practise you use only configurations that have just fixed IPs. The other methods using broadcast could be used in training or other conditions having SAP/http devices, IP addresses of which change frequently. OPC Server DriveWindow 2 7-49 8.1.4 Testing a Configuration To test the selected Current configuration, click the Test button. If the button is grayed, you probably have an old version of DriveDA (actually its communication module) installed. A dialog box containing a list of COM-ports and SAP/http devices found by the selected Current configuration is displayed. Note that the test does not check that there are drives in the RS-485 networks of a NETA-21. So it is possible that although there are SAP/http devices found, no drive is found when DriveWindow is connected to DriveDA. Note also that NETA-21 devices are found even if its panel gateway is disabled. However, no drive can be found when DriveWindow connects to DriveDA. If the test does not find any COM-ports or SAP/http devices, instead of a dialog box a message box is shown. OPC Server 7-50 DriveWindow 2 8.1.5 Saving Changes To save any changes made into the SAP/http configurations, click the OK button in the SAP/http Configuration dialog box. 8.1.6 Editing a Configuration Typically, you seldom edit the Default configuration. To edit a configuration, first select it as the Current configuration and then select Properties from the Edit or context menu. or OPC Server DriveWindow 2 7-51 The configuration Settings dialog box is displayed. Typically default values, i.e., values defined in the Default configuration, are used. An exception is that SAP/http Communication may require enabling because it may be disabled by default. Not all of the settings are shown in the dialog box. Settings for each fixed IP listed in FixedIPs are presented in a separate dialog box. OPC Server 7-52 DriveWindow 2 8.1.7 Settings for Fixed IPs To edit settings for a Fixed IP, either select it by clicking it in the Fixed IPs list in the dialog box for Settings of a configuration and then select the Properties command from the Edit menu, or right click it in the Fixed IPs list and select Properties command from the context menu displayed. or The Fixed IP Settings dialog box for the configuration is displayed. OPC Server DriveWindow 2 7-53 8.1.8 Adding and Deleting Fixed IPs Commands for adding and deleting a Fixed IP can be found in the Edit menu
