MVME-5100备件模块
所选当前配置中未找到的DDCS/UDP设备不会显示在两个列表中。所以你只能在这里操纵找到的设备。OPC服务器驱动窗口2 7-27现在您可以：•通过单击>>按钮添加所有找到的尚未包含的设备•通过单击按钮删除所有找到的当前包含的设备。•通过在“包含”列表中单击（按住Ctrl键或Shift键）并单击>按钮来选择当前包含的选定设备，从而删除这些设备。例如：OPC服务器7-28 DriveWindow 2最后单击“确定”返回配置设置对话框。现在可以在固定IP/远程子网列表中看到更改。OPC服务器驱动窗口2 7-29 7.1.11典型工作流当您来到一个以太网段中具有NETA-21设备且已配置为启用DDCS网关的站点时，您的工作流可能如下所述。第一件事是打开NETA-21设备，等待3-5分钟使其启动并运行。然后启动DriveWindow，但不要连接到OPC服务器。从网络菜单的配置子菜单中选择DDCS/UDP。从DDCS/UDP配置对话框的编辑菜单中选择新建。OPC服务器7-30驱动窗口2输入新配置的名称，您可以轻松地将其与站点关联，然后单击确定。OPC服务器驱动窗口2 7-31在新配置的设置对话框中启用DDCS/UDP通信。使其他设置更改对该配置中的所有或许多DDCS/UDP设备通用（如节点号和DDCS/UDP装置DDCS网络中分支单元的存在）。不必手动添加每个IP，可以通过单击查找附近设备来添加它们。更改设置和添加IP地址的顺序无关紧要。OPC服务器7-32 DriveWindow 2在“找到的设备”对话框中，选择要使用新配置连接的设备。OPC服务器驱动窗口2 7-33单击确定。OPC服务器7-34驱动窗口2如果DDCS/UDP设备需要与新配置的常用设置不同的特定设置，请右键单击新配置设置对话框中固定IP/远程子网列表中的IP地址，然后选择属性。也可以使用“编辑”菜单。更改您想要的设置（例如，使用特定的信道号，如果配置公用设置说明通常没有分支单元，则说明此DDCS/UDP设备的DDCS网络中存在或可能存在分支单元）。最后，单击确定。OPC服务器驱动窗口2 7-35在新配置设置对话框的设置中，完成后单击确定。OPC服务器7-36 DriveWindow 2在DDCS/UDP配置对话框中，单击确定以保存新配置并将其设置为当前配置。从网络菜单中选择网络服务器（或按Ctrl+N）。
Note that a DDCS/UDP device included in the selected Current configuration that is not found is not displayed in either of the lists. So you can manipulate here only the devices found. OPC Server DriveWindow 2 7-27 Now you can: • Add all found devices not yet included by clicking the >> button • Delete all found devices currently included by clicking the button. • Delete selected devices currently included by selecting them by clicking (with Ctrl or Shift key down) in the Include list and then clicking the > button. For example: OPC Server 7-28 DriveWindow 2 Finally click OK to get back to the dialog box for Settings of a configuration. The changes can now be seen in the Fixed IPs / Remote Subnets list. OPC Server DriveWindow 2 7-29 7.1.11 Typical Workflow When you come to a site having NETA-21 devices in an Ethernet segment already configured to have the DDCS gateway enabled, your workflow may be as explained here. The first thing is to put the NETA-21 devices on and wait 3-5 minutes to get them up and running. Then start DriveWindow, but do not connect to an OPC Server. Select DDCS/UDP from Configure submenu of the Network menu. Select New from the Edit menu in the DDCS/UDP Configuration dialog box. OPC Server 7-30 DriveWindow 2 Enter a name for the new configuration that you can easily associate with the site and click OK. OPC Server DriveWindow 2 7-31 In the Settings for the new configuration dialog box enable DDCS/UDP Communication. Make other setting changes common for all or many of the DDCS/UDP devices in this configuration (like the node numbers and presence of a branching unit in the DDCS/UDP device DDCS network). Instead of adding each IP manually, they can be added by clicking Find Near Devices. The order of changing the settings and adding the IP addresses is immaterial. OPC Server 7-32 DriveWindow 2 In the Devices Found dialog box select the devices you want to connect to with the new configuration. OPC Server DriveWindow 2 7-33 Click OK. OPC Server 7-34 DriveWindow 2 If a DDCS/UDP device requires specific settings deviating from the common settings for the new configuration, right click its IP address in the Fixed IPs / Remote Subnets list in the Settings for the new configuration dialog box and select Properties. You can use the Edit menu as well. Change the settings you want to (like use a specific channel number and state that there is, or may be, a branching unit in the DDCS network of this DDCS/UDP device if the configuration common setting states that in general there a no branching units). Finally, click OK. OPC Server DriveWindow 2 7-35 In the settings for the new configuration Settings dialog box click OK when you are done. OPC Server 7-36 DriveWindow 2 In the DDCS/UDP Configuration dialog box click OK to save the new configuration and set it as Current configuration. Select Network Servers from the Network menu (or press Ctrl+N).
