PFRL101C 2.0KN 3BSE023316R0002工业卡件
出版物KNX-TDA-EN-P-二月Kinetix旋转运动规范MP系列中惯性电机制动规范MP系列中等惯性电机负载力额定值公告MPM电机能够在下表中列出的最大径向或最大轴向轴负载下运行。所列径向载荷施加在轴外伸部的中间。下表表示L轴承的疲劳寿命为小时。这一小时的使用寿命并未考虑到因外部来源的轴承润滑脂污染而可能导致的特定应用寿命减少。最大运行速度受电机绕组限制。径向负载力额定值电机类别。数量齿隙，最大（制动器接合）弧分保持扭矩N•m（lb•in）V DC时的线圈电流A制动器响应时间B ix旋转运动规格轴上的负载力轴向负载力额定值（最大径向负载）轴向负载力（零径向负载）电机类别。编号rpm kg（lb）rpm kg（磅）rpm kg kg（lb（lb）rpm kg（lb。。)详图A轴直径公差轴直径S直径M直径螺栓圆上的孔导向直径可选轴密封请参阅第页了解MP系列电机轴密封套件信息。尺寸单位为mm（in.），带有M反馈的电源连接器MPM-A/Bxx、MPM-A/B/xx、MPM Bxx和带有M反馈和M电源连接器反馈的电源接头MPM-A/Bxx，和键槽公差MPM-A/Bxx MPM-A/B xx MPM-A/B xx轴跳动（T.I.R.）…导向偏心（T.I.R）…最大端面跳动（T.I.R.）…键槽部门
. Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications MP-Series Medium Inertia Motor Brake Specifications MP-Series Medium Inertia Motor Load Force Ratings Bulletin MPM motors are capable of operating with the maximum radial or maximum axial shaft loads listed in the following tables. Radial loads listed are applied in the middle of the shaft extension. The tables starting below represent an L bearing fatigue life of , hours. This ,-hour life does not account for possible application-specific life reduction that can occur due to bearing grease contamination from external sources. Maximum operating speed is limited by motor winding. Radial Load Force Ratings Motor Cat. No. Backlash, max (brake engaged) arc minutes Holding Torque N•m (lb•in) Coil Current at V DC A Brake Response Time B ix Rotary Motion Specifications Load Forces on Shaft Axial Load Force Ratings (maximum radial load) Axial Load Force Ratings (zero radial load) Motor Cat. No. rpm kg (lb) rpm kg (lb) rpm kg (lb) rpm kg (lb) rpm kg (lb) M MPM-A/Bxx Motors: Flush to . Pilot ± , Shaft Detail with Key MPM-A/Bxx Motors: Ø ,, (..) MPM-A/Bxx Motors: Ø ,, (..) MPM-A/Bxx Motors: Ø ,, (..) Detail A Shaft Diameter Tolerances Shaft Diameter S Diameter Holes on M Diameter Bolt Circle Pilot Diameter Optional Shaft Seal Refer to page for MP-Series motor shaft seal kit information. Dimensions are in mm (in.) Power Connector MPM-A/Bxx, MPM-A/Bxx, MPM-Bxx with M Feedback and Power Connectors MPM-A/Bxx with M Feedback and M Power Connector Feedback Connector Connector housings can be rotated within a range of ° Shaft, Pilot, and Keyway Tolerances MPM-A/Bxx MPM-A/Bxx MPM-A/Bxx Shaft Runout (T.I.R.) . . . Pilot Eccentricity (T.I.R.) . . . Max Face Runout (T.I.R.) . . . Keyway Dept
