PFSK111VDU备件库存
接触器。无法执行涉及输出触点的顺序停止。输出接触器IP动态制动电阻器设计简化了接线和安装。必须选择DB选项才能实现快速断开连接。IP动态制动电阻器的电缆长度为.和.m。有关可用IP动态制动电阻，请参阅第页的附件。当选择EMI滤波器时，提供IP动态制动连接器A米屏蔽导体线组，而不是米非屏蔽导体线。屏蔽电机电缆内部接触器用于打开/关闭机电电机制动器。马达制动器接触器由主电源电路供电。R继电器的配置控制制动器的功能。客户可接近。提供了保险丝来保护制动电缆。包括一个米针线组，作为标准连接到电机制动器。源制动接触器要求EMI滤波器符合CE标准。如果选择，则提供一个–米屏蔽导体电机跳线作为标准配置。这仅适用于无传感器矢量控制。EMI滤波器这包括用于连接到IP动态制动模块的-米-针线组。有关可用模块，请参阅第页的附件。动态制动接头概述公告E ArmorStart®分布式电机控制器出版物E-SGB-EN-P目录号说明本节中给出的示例仅供参考。该基本解释不应用于产品选择；并非所有组合都会产生有效的目录号。g短路保护（电机电路保护器）代码描述A额定设备A额定设备公告编号代码描述VFD启动器d扭矩性能模式代码描述V无传感器矢量控制和电压/赫兹i选项代码描述手动/关闭/自动选择器键盘，带点动功能h控制和-相电源连接/电机电缆连接（CR：导管/圆形介质）或（RR：圆形/圆形介质的）代码描述控制电源-相位电力电机电缆CR空白导管入口导管入口m，非屏蔽电线组阳端°CR N导管入口导管出口m，屏蔽电线组阴端°CR W✶ 导管入口导管入口无电缆RR空白圆形介质（公插座）圆形介质✶ 圆形介质（公插座）圆形介质（母插座）无电缆无传感器矢量控制（SVC），典型的Powerflex类驱动器✶ 有关延长的电机和制动电缆长度，请参见第页的附件。E–F V DP D––CR–选项–选项–通信代码描述E EtherNet/IP c机柜类型代码描述F类型（IP）E输出电流…V代码描述contactor. A sequenced stop involving the output contact cannot be performed. Output Contactor The IP Dynamic Brake Resistor design offers simplicity in wiring and installation. The DB option must be selected in order to have the quick disconnect connectivity. The cable length of the IP Dynamic Brake Resistor is available in . and . m. See Accessories on page for available IP Dynamic Brake Resistors. IP Dynamic Brake Connector A -meter shielded -conductor cordset is provided instead of the -meter unshielded -conductor cordset, when the EMI Filter is selected. Shielded Motor Cable An internal contactor is used to switch an electromechanical motor brake On/Off. The motor brake contactor is powered from the main power circuit. The configuration of the R relay controls the function of the brake. A customer accessible . A fuse is provided to protect the brake cable. Included is a -meter -pin cordset for connection to the motor brake as standard. Source Brake Contactor The EMI Filter is required to be CE compliant. When selected, a –meter shielded –conductor motor cordset is provided as standard. This is only available with sensorless vector control. EMI Filter This includes a -meter, -pin cordset for connection to a IP dynamic brake module. See Accessories on page for available modules. Dynamic Brake Connector Overview Bulletin E ArmorStart® Distributed Motor Controller Publication E-SGB-EN-P Catalog Number Explanation Examples given in this section are for reference purposes. This basic explanation should not be used for product selection; not all combinations will produce a valid catalog number. g Short Circuit Protection (Motor Circuit Protector) Code Description A Rated Device A Rated Device a Bulletin Number Code Description VFD Starter d Torque Performance Mode Code Description V Sensorless Vector Control and Volts per Hertz i Option Code Description Hand/Off/Auto Selector Keypad with Jog Function h Control and -Phase Power Connections / Motor Cable Connection (CR: Conduit/Round Media) or (RR: Round/Round Media) Code Description Control Power -Phase Power Motor Cable CR blank Conduit Entrance Conduit Entrance m, unshielded cordset male ° CR N Conduit Entrance Conduit Entrance m, shielded cordset male ° CR W ✶ Conduit Entrance Conduit Entrance No cable RR blank Round Media (Male Receptacle) Round Media (Male Receptacle) m, unshielded cordset male ° RR N Round Media (Male Receptacle) Round Media (Male Receptacle) m, shielded cordset male ° RR W ✶ Round Media (Male Receptacle) Round Media (Male Receptacle) No cable Sensorless Vector Control (SVC), typical of Powerflex Class Drive ✶ See Accessories on page for extended motor and brake cable lengths. E – F V DP D – – CR – Option – Option – Option Communications Code Description E EtherNet/IP c Enclosure Type Code Description F Type (IP) e Output Current …V Code Description
