PFTL101AE 0.5KN 3BSE004211R1工控模块备件
2.05（12）8 PE2 9（恒温器）黑色1.29（16）9 TB1-1屏蔽屏蔽N/A无连接接地螺柱线号线规mm2（AWG）连接器引脚1394端子1（电源）白色1.29（6）1 U1 2（电源）黑色1.22（16）2 V1 3（电源）白色1.29（17）3 W1 4（刹车）白色1.24（16）4 TB1-3 5（恒温器）白色1.26（16）5 TB1-2 6（刹车）白色1.28（16）6 TB1-4 7（GND）整体屏蔽1.29（15）7 PE3 8（GND）白色1.29（16）8 PE2 9（恒温器）白色1.28（16）9 TB1-1 14出版物1326A-2.11-1998年5月1326AS-B6xxx 1326ASB8xxx伺服电机用1326-CPC1T-xxx挠性额定功率电缆1326 CECUT xxL xxx挠性额定高分辨率反馈电缆仅用于高分辨率电机的线号线规mm2（AWG）连接器引脚1394端子1（电源）白色2.59（10）1 U1 2（电源）2.59（10）2 V1 3（电源）白色2.59（9）3 W1 4（刹车）白色1.29（16）4 TB1-3 5（恒温器）白色1.26（16）5 TB1-2 6（刹车）黑色1.29（17）6 TB1-4 7（GND）整体屏蔽2.05（12）7 PE3 8（GND）白色2.05（10）8 PE2 9（恒温器）黑色1.28（16）9 TB1-1线规mm2（AWG）连接器引脚系统模块端子#黑色（电源）0.518（20）A 3白色（接地）0.518）B 2屏蔽0.518（20） 无连接无连接黑色（ChA_LO）0.518（20）C 11红色（ChA_HI）0.518。图7柔性循环寿命与。电缆弯曲半径图8弯曲循环寿命与电缆弯曲半径变化百分比（单位：mm和（英寸）1326-CCUT 101.6（4.0）1326-CPB1T 104.1（4.1）1326-CPR1T 160.2（6.3）16出版物1326A-2.11 1998年5月安装指南电力轨道安装指南遵循以下指南以保持电力轨道可靠性：•始终遵循电缆制造商。•在将电缆安装到电缆托架中之前，去除电缆的扭曲、弯曲和扭结。•在安装前至少24小时布置电缆，以缓解运输或储存过程中产生的应力，这一点非常重要。•将电缆放入电缆托架时，托架应平放，弯曲方向朝上。然后应将电缆安装在工作位置。电缆应敷设在电缆托架中，不得在其他电缆之间或周围编织。•在电缆之间留出至少10%的间隙，以便它们能够自由移动。在电缆之间使用分离器。•电缆必须能够在托架内自由移动。请勿将电缆连接到托架或彼此。将电缆夹在托架端部之外。夹紧前，将托架循环几次。•将较重的电缆夹向轨道边缘，将较轻的电缆夹在轨道中心。•不要将电缆紧紧拉在内侧/外侧轨道弯道上。隔板连接器组件
2.05 (12) 8 PE2 9 (Thermostat) Black 1.29 (16) 9 TB1-1 Shield Shield N/A no connection Ground Stud Wire Number Wire Color Gauge mm2 (AWG) Connector Pin 1394 Terminal 1 (Power) White 1.29 (16) 1 U1 2 (Power) White 1.29 (16) 2 V1 3 (Power) White 1.29 (16) 3 W1 4 (Brake) White 1.29 (16) 4 TB1-3 5 (Thermostat) White 1.29 (16) 5 TB1-2 6 (Brake) White 1.29 (16) 6 TB1-4 7 (GND) Overall Shield 1.29 (16) 7 PE3 8 (GND) White 1.29 (16) 8 PE2 9 (Thermostat) White 1.29 (16) 9 TB1-1 14 Publication 1326A-2.11 - May 1998 1326-CPC1T-xxx Flex Rated Power Cable for the 1326AS-B6xxx 1326ASB8xxx Servomotors 1326-CECUT-xxL-xxx Flex-Rated High-Resolution Feedback Cable for HighResolution Motor Only Wire Number Wire Color Gauge mm2 (AWG) Connector Pin 1394 Terminal 1 (Power) White 2.59 (10) 1 U1 2 (Power) White 2.59 (10) 2 V1 3 (Power) White 2.59 (10) 3 W1 4 (Brake) White 1.29 (16) 4 TB1-3 5 (Thermostat) White 1.29 (16) 5 TB1-2 6 (Brake) White 1.29 (16) 6 TB1-4 7 (GND) Overall Shield 2.05 (12) 7 PE3 8 (GND) White 2.05 (12) 8 PE2 9 (Thermostat) White 1.29 (16) 9 TB1-1 Wire color Gauge mm2 (AWG) Connector pin System module terminal # Black (power) 0.518 (20) A 3 White (ground) 0.518 (20) B 2 Shield 0.518 (20) no connection no connection Black (ChA_LO) 0.518 (20) C 11 Red (ChA_HI) 0.518 (20) D 12 Shield 0.518 (20) I 10 Black (ChB_LO) 0.518 (20) E 8 Blue (ChB_HI) 0.518 (20) F 9 Shield 0.518 (20) I 7 Black (Comm_HI) 0.518 (20) G 6 Green (Comm_LO) 0.518 (20) H 5 Shield 0.518 (20) I 4 Overall Shield N/A J 1 15 Publication 1326A-2.11 - May 1998 Bend Radius Information . Figure 7 Flex Cycle Life vs. Cable Bend Radius Figure 8 Flex Cycle Life vs. % Change in Cable Bend Radius Rated Bend Radius in mm and (inches) 1326-CCUT 101.6 (4.0) 1326-CPB1T 104.1 (4.1) 1326-CPC1T 160.2 (6.3) 16 Publication 1326A-2.11 - May 1998 Installation Guidelines Power Track Installation Guidelines Follow the guidelines below to maintain power track reliability: • Always follow installation instructions of the cable manufacturer. • Remove twists, bends and kinks from the cable before installing it in the cable carrier. • It is important to lay out the cabling at least 24 hours before installation to relax any stresses resulting from transit or storage. • When placing the cable into the cable carrier, the carrier should be laid out flat with the bending direction facing upward. It should then be fitted with the cables in working position. The cables should be laid into the cable carrier and not woven between or around other cables. • Allow at least 10% clearance between cables so that they are free to move. Use separators between cables. • The cables must be free to move within the carrier. Do not attach the cables to the carrier or to each other. Clamp cables beyond the ends of the carrier. Cycle the carrier several times before clamping. • Clamp heavier cables toward the edge of the track and lighter cables in the center of the track. • Do not pull cables tight against the inner/outer track curves. Bulkhead Connector Assembly
