PP881 3BSE092978R1模拟量输入模块
2.在DriveExplorer树视图中，单击22-COMM-E EtherNet/IP，如图1所示。3.单击信息图标以显示适配器的属性屏幕。4.“版本：”字段显示适配器固件的当前版本（例如1.007）。图1 DriveExplorer窗口中的信息图标提示：使用5.01或更高版本DriveExplorer Lite/Full单击22-COMM-E适配器时，适配器固件版本也会显示在DriveExplorer窗口的右侧窗格中。步骤2步骤3步骤4 4 22-COMM-E EtherNet/IP适配器固件v1008使用DriveExecutive 1。启动DriveExecutive并与连接到适配器的驱动器联机。2.在DriveExecutive树视图中，单击22-COMM-E，如图2.3所示。单击信息图标以显示适配器的Properties屏幕。4.“版本：”字段显示适配器固件的当前版本（例如1.007）。图2 DriveExecutive窗口固件闪存中的信息图标本节介绍闪存升级适配器固件的步骤。Allen-Bradley网站上提供了驱动器、通信适配器和外围设备的闪存套件，网址为http://www.ab.com/support/abdrives/webupdate。步骤3步骤2步骤4！注意：存在永久性设备损坏的风险。启动闪存更新后，在下载完成且适配器MOD状态指示灯开始闪烁绿色之前，不要断开驱动器（或22-XCOMM-DC-BASE外部通信套件（如果使用））的电源。如果在此之前断开电源，适配器可能会永久损坏。无法修复以这种方式损坏的适配器。22-COMM-E EtherNet/IP适配器固件v1.008 5安装闪存套件1。请访问Allen-Bradley Web更新网站http://www.ab.com/支持/abdrives/webupdate，并为22-COMM-E适配器安装闪存套件。（这也会自动在您的计算机上安装ControlFLASH软件。）2.您现在可以使用DriveExplorer、DriveExecutive、ControlFLASH或超级终端来更新适配器。
2. In the DriveExplorer treeview, click on 22-COMM-E EtherNet/IP as shown in Figure 1. 3. Click the information icon to display the adapter’s properties screen. 4. The “Revision:” field shows the present revision (for example, 1.007) of the adapter firmware. Figure 1 Information Icon in DriveExplorer Window TIP: When clicking on the 22-COMM-E adapter using version 5.01 or higher DriveExplorer Lite/Full, the adapter firmware revision is also shown in the right pane of the DriveExplorer window. Step 2 Step 3 Step 4 4 22-COMM-E EtherNet/IP Adapter Firmware v1.008 Using DriveExecutive 1. Launch DriveExecutive and go online with the drive that is connected to the adapter. 2. In the DriveExecutive treeview, click on 22-COMM-E as shown in Figure 2. 3. Click the information icon to display the adapter’s Properties screen. 4. The “Revision:” field shows the present revision (for example, 1.007) of the adapter firmware. Figure 2 Information Icon in DriveExecutive Window Firmware Flashing This section describes procedures to flash upgrade your adapter firmware. Flash kits for drives, communications adapters, and peripherals are provided on the Allen-Bradley Web Updates site located at http://www.ab.com/ support/abdrives/webupdate. Step 3 Step 2 Step 4 ! ATTENTION: Risk of permanent equipment damage exists. Once a flash update has been started, do not remove power from the drive (or the 22-XCOMM-DC-BASE External Comms Kit, if used) until after the download has completed and the adapter MOD status indicator starts FLASHING GREEN. If power is removed before this occurs, the adapter may be permanently damaged. An adapter that has been damaged in this way cannot be repaired. 22-COMM-E EtherNet/IP Adapter Firmware v1.008 5 Installing the Flash Kit 1. Go to the Allen-Bradley Web Updates site at http://www.ab.com/ support/abdrives/webupdate and install the flash kit for the 22-COMM-E adapter. (This also automatically installs the ControlFLASH software on your computer.) 2. You are now ready to use DriveExplorer, DriveExecutive, ControlFLASH or HyperTerminal to update the adapter.
