PP886 3BSE092980R1处理器模块
使用22-RJ45CBL-Cxx通信电缆或AK-U0-RJ45-TB2P接线板适配器和适当的双绞线，将一端连接到通信套件的配对DSI连接器，另一端连接到驱动器底部的RJ45端口。重要提示：在配置适配器之前，请始终进行此连接。此外，始终将连接驱动器的参数A103-[Comm Data Rate]设置为“4”（19.2 K）。➎ RS232 DF1端口连接，用于PC使用软件工具。使用1203-SFC电缆，将一端连接到通信套件的配套串行连接器，另一端连接到PC COM端口。重要提示：在配置适配器之前，始终进行此连接。此外，在计算机与此端口之间建立通信时，始终将波特率设置为“19.2 K”。注意：此端口在22-COMM-L或22-COMM-P适配器上不起作用。（1） 用于为通信套件供电的直流电源或交流至直流转换器必须能够在18…27V直流电压下提供至少150 mA的电流。此外，其连接器必须为“针筒式”结构，具有2mm的针。（2） 要为其他通信套件供电，请参阅第4页的“为菊花链通信套件供电”。网络取决于已安装的22-COMM-*适配器驱动协议数据速率DSI 19.2 kbps项目描述连接程序+-通过DSI电缆网络从驱动器提供的12V DC下的驱动60 mA对于所有网络协议均无，除了：DeviceNet 24V DC下的60 mA电源要求（1）（1）由于通信套件由标称24V DC供电，此表中列出的电流消耗与通信适配器标签上显示的值不同，该值基于适配器由驱动器的5V DC供电。
Using a 22-RJ45CBL-Cxx Communications Cable or AK-U0-RJ45-TB2P Terminal Block Adapter and appropriate twisted pair cable, connect one end into the mating DSI connector of the Comms Kit and the other end into the RJ45 port on the bottom of the drive. Important: Always make this connection before configuring the adapter. Also, always set the connected drive’s parameter A103 - [Comm Data Rate] to “4” (19.2 K). ➎ RS232 DF1 Port Connection for PC to use software tools. Using a 1203-SFC cable, connect one end into the mating Serial connector of the Comms Kit and the other end into a PC COM port. Important: Always make this connection before configuring the adapter. Also, when establishing communication between the computer and this port always set the baud rate to “19.2 K.” NOTE: This port is not functional on a 22-COMM-L or 22-COMM-P adapter. (1) The DC power source or AC-to-DC converter used to power the Comms Kit must be capable of providing a minimum of 150 mA @ 18…27V DC. Also, its connector must be of “pin and barrel” construction with a 2mm pin. (2) To power additional Comms Kits, see Powering Daisy-Chained Comms Kits on page 4. Network Dependent on installed 22-COMM-* adapter Drive Protocol Data Rate DSI 19.2 kbps Item Description Connection Procedure + - Drive 60 mA at 12V DC supplied from drive via DSI cable Network None for all network protocols except: DeviceNet 60 mA at 24V DC DC Power Supply Requirement (1) (1) Since the Comms Kit is powered by a nominal 24V DC, the current consumption listed in this table differs from the value shown on the label of the communication adapter, which is based on the adapter being powered by 5V DC from the drive.
