您的浏览器版本过低,为保证更佳的浏览体验,请点击更新高版本浏览器

以后再说X

欢迎访问瑞昌明盛自动化设备有限公司网站!

图片名

全国订购热线:
+86 15270269218E-mail:stodcdcs@gmail.com

ABB >>

A-B>>

GE>>

BENTLY>>

PPD113B01-10-150000 3BHE023784R1023工控模块机器人备件

PPD113B01-10-150000 3BHE023784R1023工控模块机器人备件

PPD113B01-10-150000 3BHE023784R1023工控模块机器人备件它应用于所有双通道双接触器系统。如果其中一个接触器未能隔离电源,则垫控制单元将锁定并防止另一个接触器重新通电,直到故障得到纠正。5.8最终传感器垫布局考虑到这些因素后,现在可以检查并最终确定传感器垫布局。考虑机器响应时间是否与初始计算有所不同。在可能的情况下,应在检测区的外侧边缘设置垫子和电线。这简化了安装和更...

  • 功能特性
  • 参数规格
  • 视频
  • 应用案例
  • 下载

PPD113B01-10-150000 3BHE023784R1023工控模块机器人备件

    PPD113B01-10-150000 3BHE023784R1023工控模块机器人备件

    它应用于所有双通道双接触器系统。如果其中一个接触器未能隔离电源,则垫控制单元将锁定并防止另一个接触器重新通电,直到故障得到纠正。5.8最终传感器垫布局考虑到这些因素后,现在可以检查并最终确定传感器垫布局。考虑机器响应时间是否与初始计算有所不同。在可能的情况下,应在检测区的外侧边缘设置垫子和电线。这简化了安装和更换(如果需要),并且所有布线都受到周边装饰的保护。5.9布线所有系统布线必须防止机械损坏,并适当密封以适应操作环境。提供防水对接接头用于垫子到垫子的连接,并由边缘镶边保护。如果需要在地板上布线,440F-T3230导线导管可以提供适当的保护。其他电线线路应使用导管或线槽。控制装置的密封完整性必须通过使用尺寸正确且紧固的导管配件或电缆压盖保持在IP65。布线实践必须符合EN 60204-1第14条的要求。注意:为了确保110/230V电源的隔离,输入电源必须单独布线,并通过用于输出接线的单独配件或压盖进入控制单元。从控制单元到垫子的电线可以使用导管埋在地板中,或通过边缘装饰件。此类安装建议使用挠性导管。

    It should be used in all dual channel two contactor systems. If one of the contactors fails to isolate the power, the mat control unit will lock out and prevent the re-energisation of the other contactor until the fault is rectified. 5.8 FINAL SENSOR MAT LAYOUT Having considered these factors, the sensor mat layout can now be checked and finalised. Consider whether the machine response time has changed from the initial calculations. Whenever possible, mats should be arranged with the wires at the outside edge of the detection zone. This simplifies installation and replacement if required and all wiring is protected by the perimeter trim. 5.9 WIRING All system wiring must be protected from mechanical damage and suitably sealed for the operating environment. Waterproof butt connectors are supplied for mat to mat connections and are protected by the edge trim. Where wire runs are required across the floor, the 440F-T3230 wire guide can provide suitable protection. Conduit or trunking should be used for other wire runs. The sealing integrity of the control unit must be maintained by the use of correctly sized and tightened conduit fittings or cable glands to IP65. Wiring practices must be in accordance with EN 60204-1 Clause 14. NOTE: In order to ensure the isolation of the 110/230V supply, the input power supply must be separately routed and enter the control unit via separate fittings or glands to those used for the output wiring. Wiring from the control unit to the mat may be buried in the floor using conduit, or pass via the edge trim. Flexible conduit is recommended for this type of installation. 

    11.jpg

    微信图片_20211117105524_副本.jpg



    品牌:ABB

    型号:PPD113B01-10-150000 3BHE023784R1023 

    产地:美国

    质保:365天

    成色:全新/二手

    发货方式:快递发货


图片名 客服

在线客服 客服一号