BENTLY 3500/22M 138607-01 工控DCS系统备件
拆下发射器电缆上的蓝色标记和接收器电缆上的白色标记，以便对电缆进行适当标记，以备将来使用。各个灯阵列通过该连接到控制器供电。请参阅与您使用的特定控制器对应的安装说明，以了解有关控制器接线和连接的更多详细信息。校准这是设置中的关键步骤，因为传感器操作取决于发射器和接收器的正确校准。通过使用接收器单元上的绿色LED作为正确对准的指示，简化了该过程。水平对齐1.将接收器对准发射器（光源）90°，并验证接收器和发射器上的红色状态LED是否均已打开。2.缓慢旋转接收器，使其面向发射器，并注意这些红色LED熄灭且绿色对齐LED亮起的点。3.继续旋转接收器，远离发射器，直到绿色LED再次熄灭，和红色LED亮起。请注意发生这种情况的点。4.对于水平居中，在红色LED熄灭的两个点之间旋转阵列一半。红色LED熄灭绿色LED打开红色LED打开45MLA未对齐对齐绿色LED关闭3垂直对齐1。从两个阵列彼此平行开始，向下滑动接收器并记下两个阵列上红色LED点亮的点。这表示接收器不再与发射器对齐。2.向上滑动接收器，直到接收器上的红色LED熄灭，绿色LED点亮。这表明两个阵列对齐。3.继续向上滑动接收器，注意绿色LED熄灭，两个红色LED点亮的点，再次指示未对准。4.对于垂直居中，将接收器放置在红色LED熄灭的两个点之间的中间位置。接线图45MLA是一个“三盒系统”-每个设置都由发射器阵列、接收器阵列和外部控制器组成。45MLA阵列具有一个M12、8针内螺纹QD，该QD连接到连接电缆445L-AC9RJx（x=3、5或8米长）。
Remove the blue mark on the transmitter cable and the white mark on the receiver cable to properly mark the cable for future use. Each light array is powered by this connection to the controller. Refer to the installation instructions that correspond to the specific controller you are using for more details on controller wiring and connections. Calibration This is a critical step in setup, as sensor operation depends on the correct calibration of the transmitter and receiver. This process is simplified by using the green LED on the receiver unit as an indication of correct alignment. Horizontal alignment 1. Align the receiver 90 ° to the transmitter (light source) and verify that the red status LEDs on the receiver and transmitter are turned on. 2. Slowly rotate the receiver so that it faces the transmitter and note that these red LEDs are off and the green aligns with the points where the LEDs are lit. 3. Continue to rotate the receiver away from the transmitter until the green LED turns off again and the red LED turns on. Note the point at which this occurs. 4. For horizontal centering, rotate the array half between the two points where the red LED is off. Red LED off Green LED on Red LED on 45MLA misaligned Green LED off 3 Vertical alignment 1. Starting with the two arrays parallel to each other, slide the receiver down and note the points where the red LEDs are lit on both arrays. This means that the receiver is no longer aligned with the transmitter. 2. Slide the receiver upward until the red LED on the receiver is off and the green LED is on. This indicates that the two arrays are aligned. 3. Continue to slide the receiver upward. Note that the green LED is off, and the two red LED lit points indicate misalignment again. 4. For vertical centering, place the receiver midway between the two points where the red LED is off. Wiring diagram 45MLA is a "three box system" - each setup consists of a transmitter array, a receiver array, and an external controller. The 45MLA array has an M12, 8-pin female QD that connects to the connecting cable 445L-AC9RJx (x=3, 5, or 8 meters long).
