BC810K01 3BSE031154R1工控模块系统备件
电缆尾光纤（仅用于连接到45MLA控制器）附件提供的附件可调安装套件（445L-AF6143）所需附件（控制器）控制器模拟型号：45MLA-CTRL-AG控制器基本型号：45MLA-CTRL-BSC控制器I/O型号：45ML A-CTRL控制器RS485:45ML-CTRL-485控制器CAN:45ML-TRL-CAN所需附件（灯阵列至控制器连接电缆）3 m M12-RJ45:4455L-C8RJ3 5 m M12-RJ45：445L-C8RJ5 8 m M12-J445:445L-C8RJ8最大系统长度不能超过10 m（32.8 ft）可选附件可调平面安装支架：445L-A6149平面安装套件：445L-AF6145级联阵列延长跳线，M12 8针，3M:445L-A8PC3 2安装说明1。发射器和接收器轮廓都衬有连续的凹槽，以连接到安装支架，允许这些支架沿外壳长度连接在任何位置。注：也可单独购买平面安装套件。2.对准发射器和接收器，使两个单元彼此平行，并且带有光电传感器元件（和透明塑料透镜）的侧面彼此面对。3.请注意，接收器（蓝色连接器）可能对干扰光敏感。任何其他外部光源，包括任何光电传感器、阵列或反射表面的发射器，都不应指向接收器外壳。尽管45MLA能够承受明亮的阳光，但最好安装接收器外壳，使阳光不会直接照射到接收器透镜的弯曲前部区域。电气安装两个灯阵列必须通过RJ45连接器连接到控制器。为了便于连接，发射器的尾光纤连接器有一个白色标记，接收器有一个蓝色标记。确保用白色标记将发射器连接到控制器上的插头，用蓝色标记将接收器连接到插头。阵列LED描述颜色含义绿色（控制器上也有LED D1）光阵列对准偏离目标存在或阵列未对准绿色目标不存在，阵列对齐且在范围内绿色（闪烁）光强度不足红色（控制器上还有LED D2）光阵列状态关闭目标不存在（和阵列对齐）红色目标存在（或阵列未对齐）红色（闪烁）高度测量错误此外，提供的连接器电缆两端都连接有蓝色和白色环。
Cable pigtail (only for connecting to 45MLA controller) Accessories provided Accessories Adjustable installation kit (445L-AF6143) Required accessories (controller) Controller analog model: 45MLA-CTRL-AG controller basic model: 45MLA-CTRL-BSC controller I/O model: 45ML A-CTRL controller RS485: 45ML-CTRL-485 controller CAN: 45ML-TRL-CAN Required accessories (light array to controller connecting cable) 3 m M12-RJ45: 4455L-C8RJ3 5 m M12-RJ45: 445L-C8RJ5 8 m M12-J445: 445L-C8RJ8 The maximum system length cannot exceed 10 m (32.8 ft) Optional accessories Adjustable plane mounting bracket: 445L-A6149 Plane mounting kit: 445L-AF6145 Cascade array extension jumper, M12 8-pin, 3M: 445L-A8PC3 2 Installation instructions 1. The transmitter and receiver contours are lined with continuous grooves to connect to the mounting brackets, allowing them to be connected anywhere along the length of the housing. Note: Flat mount kits can also be purchased separately. 2. Align the transmitter and receiver so that the two units are parallel to each other and the sides with photoelectric sensor elements (and transparent plastic lenses) face each other. 3. Please note that the receiver (blue connector) may be sensitive to interference light. Any other external light source, including any photoelectric sensor, array or emitter with reflective surface, shall not point to the receiver housing. Although 45MLA can withstand bright sunlight, it is better to install the receiver housing so that sunlight does not directly shine on the curved front area of the receiver lens. The two lamp arrays for electrical installation must be connected to the controller through RJ45 connectors. For easy connection, the transmitter's pigtail connector has a white mark and the receiver has a blue mark. Make sure the transmitter is connected to the plug on the controller with a white mark and the receiver is connected to the plug with a blue mark. Array LED description Color meaning Green (LED D1 is also available on the controller) Optical array alignment deviates from the target or the array is misaligned Green target does not exist, the array is aligned and within the range Green (flashing) light intensity is insufficient Red (LED D2 is also available on the controller) Optical array status Off Target does not exist (aligned with the array) Red target exists (or the array is misaligned) Red (flashing) height measurement error In addition, The supplied connector cable is connected with blue and white rings at both ends.
