PU518 3BSE018680R1励磁系统控制卡
这些接头是控制单元的垫连接，并连接到单元外部的外部快速连接插头。13.重新检查接线连接，包括机器控制系统接线的连接或修改。更换盖。将盖固定在相关单元上。断开机器原动机与最终接触器的连接，使机器无法移动。6.3检查机械安装1.检查传感器垫、周边装饰件和联合装饰件是否完好无损，是否正确定位和固定。检查是否达到了设计的安全距离。2.检查除了通过垫子之外，是否无法进入危险区域，并且任何固定防护装置等是否根据设计进行了定位，并且是否安全。3.检查危险区和垫子系统之间是否有人。4.检查当前或可预见的环境条件是否符合设计阶段考虑的环境条件。5.检查安装是否无设计阶段未预见到的危险。6.检查所有警告通知是否到位。7.检查是否已安装所需的任何其他保护措施。6.4检查电气功能1.确保垫子上没有人员和设备。暂时断开机器控制系统提供的任何自动复位功能。恢复机器电源，但确保机器原动机仍与机器最终接触器断开。A、 仅手动模式（使用440F-C28013控制单元时不相关）2.检查控制单元：-绿色LED-电源亮起-绿色LED–手动复位亮起-复位按钮中的复位灯亮起-红色LED-机器启用关闭。3。按下并松开重置按钮-检查MACHINE ENABLED LED（机器启用LED）是否亮起，重置灯是否熄灭-站在垫子上，检查MACHINEENABLED LED是否熄灭。4.离开垫子，检查MACCHINE ENABLED（机器启用）LED是否熄灭，重置按钮是否亮起。-按下并松开重置按钮，检查机器启用LED是否亮起，重置按钮是否熄灭。5.重复上述测试，检查远程重置按钮和指示灯（如果安装）。33 6.重复上述步骤，检查连接到垫子系统的任何状态监测的正确操作。B、 仅限自动重置模式（使用440F-C28013控制单元时不相关）2.检查控制单元上的：-绿色LED-电源亮起-绿色LED–机器已启用。3.站在垫子上，检查机器已启用LED是否熄灭。4.离开垫子，检查机器启用LED是否亮起。5。重复上述步骤，以检查连接到垫系统的任何状态监测的正确操作。440F-C28013控制单元功能仅自动重置模式1。检查控制单元：绿色LED-电源亮起绿色LED-机器启用亮起通道故障LED 1至8亮起绿色，与安装的垫子数量相匹配。
These connectors are pad connections for the control unit and are connected to the external quick connect plug outside the unit. 13. Recheck the wiring connection, including the connection or modification of the machine control system wiring. Replace the cover. Secure the cover on the relevant unit. Disconnect the machine prime mover from the final contactor so that the machine cannot move. 6.3 Check the mechanical installation 1. Check whether the sensor pad, peripheral trim and joint trim are intact and correctly positioned and fixed. Check whether the designed safety distance is reached. 2. Check whether it is impossible to enter the dangerous area except through the mat, and whether any fixed protective devices are positioned according to the design and safe. 3. Check if there is anyone between the hazardous area and the mat subsystem. 4. Check whether the current or foreseeable environmental conditions meet the environmental conditions considered at the design stage. 5. Check whether the installation is free from dangers not foreseen at the design stage. 6. Check whether all warning notices are in place. 7. Check whether any other protective measures required have been installed. 6.4 Check the electrical function 1. Make sure there are no people and equipment on the mat. Temporarily disconnect any automatic reset functions provided by the machine control system. Restore the machine power, but ensure that the machine prime mover is still disconnected from the final contactor of the machine. A. Manual mode only (not relevant when using 440F-C28013 control unit) 2. Check the control unit: - green LED - power on - green LED - manual reset on - reset lamp in reset button on - red LED - machine on/off. 3。 Press and release the reset button - check that the MACHINE ENABLED LED is on and the reset lamp is off - stand on the mat and check that the MACHINE ENABLED LED is off. 4. Leave the mat and check whether the MACCHINE ENABLED LED is off and the reset button is on- Press and release the reset button and check that the machine enable LED is on and the reset button is off. 5. Repeat the above test and check the remote reset button and indicator (if installed). 33 6. Repeat the above steps to check the correct operation of any condition monitoring connected to the mat subsystem. B. Automatic reset mode only (not relevant when using the 440F-C28013 control unit) 2. Check the: - green LED - power on - green LED - machine enabled on the control unit. 3. Stand on the mat and check whether the machine enabled LED is off. 4. Leave the mat and check if the machine enable LED is lit. 5。 Repeat the above steps in order to check the correct operation of any condition monitoring connected to the cushion system. The 440F-C28013 control unit function only automatically resets mode 1. Check the control unit: green LED - power on green LED - machine enable on channel fault LEDs 1 to 8 on green, matching the number of mats installed.
