R911190045 HDS03.2-W100N-HT20-01-FW工控备件模块
27 440F-T3210、440F-T3310和440F-T3510 440F-T3211和440F-T3411对于外部拐角装饰件，使用440F-T3014。对于内部拐角装饰件使用440F-T3105，440F-T3310和440F-T3510使用带挠性导管的应力消除夹具MAT 1 MAT 2 MAT 1 MAT 2 MAT3 MAT 1 MAT 2 45°45°MAT 3 MAT 4将所有装饰件切割成45°，如图所示。标记地板上的边缘装饰件固定位置，使装饰件与垫重叠。以装饰件上的孔为导向，标记并钻孔地板（如果需要，安装塞子）。清洁地板，并使用沉头螺钉将垫子和边缘装饰件固定到位，以适应应用。安装周边装饰件时，确保装饰件和地板之间或顶部和底部之间（取决于装饰件类型）没有任何电线被夹住或压碎。如果电线可能被夹住或拉动，应在电线离开周边装饰的地方使用应变消除夹。所有电线应采用适当的导管进行保护。如果可能，电线/导管不应穿过可能会绊倒的地板区域。如果无法避免这种情况，应将电线/导管封装在我们的《保护电线指南》440F-T3230中（参见第37页的可用备件）。6.2控制单元的安装和布线（也可参考第4节图7、第5.3.7节和第5.7节）控制单元应按照供应进行安装。除本手册所述的程序或连接外，不得对其进行修改或进行任何其他程序或连接。通过小心敲击（440F-C4000P）或钻出（440F-C4 000S，440FC28013）要使用的电缆入口位置来准备控制单元。输入电源必须单独布线，并通过与输出接线所用电源的单独入口进入控制单元。装载t控制单元处于其计划位置。控制单元端子的所有接线必须使用提供的导线类型或多股导管电缆/开关设备电缆/设备导线，导线为0.5-1.5mm2。电缆进入控制单元（440F-C4000P、440F-C400S和440F-C28013）时，必须使用防护等级为IP65的压盖或适配器。确保压盖或适配器的尺寸合适并完全拧紧。必须使用提供的绝缘针脚压褶。这种电线和端子组合避免了因过度拧紧或振动而导致的松股短路或开路的可能性。确保使用合适的棘轮型压接工具。
27 440F-T3210, 440F-T3310 and 440F-T3510 440F-T3211 and 440F-T3411 For exterior corner trim, use 440F-T3014. For the interior corner trim, use 440F-T3105440F-T3310 and 440F-T3510 to cut all the trims to 45 ° using the stress relief fixture MAT 1 MAT 2 MAT 1 MAT 2 MAT3 MAT 1 MAT 2 45 ° 45 ° MAT 3 MAT 4 with flexible conduit, as shown in the figure. Mark the fixing position of the edge trim on the floor so that the trim overlaps the pad. Using the holes in the trim as a guide, mark and drill the floor (install plugs if necessary). Clean the floor and fix the mat and edge trim in place with countersunk screws to suit the application. When installing the perimeter trim, ensure that no wires are trapped or crushed between the trim and the floor or between the top and bottom (depending on the trim type). If the wire may be pinched or pulled, strain relief clips should be used where the wire leaves the perimeter trim. All wires shall be protected by suitable conduits. Where possible, wires/conduits should not pass through floor areas where tripping may occur. If this cannot be avoided, the wire/conduit should be enclosed in our Guide to Protecting Wires 440F-T3230 (see available spare parts on page 37). 6.2 Installation and wiring of the control unit (also refer to Section 4, Figure 7, Section 5.3.7 and Section 5.7) The control unit shall be installed according to the supply. Except for the procedures or connections described in this manual, they shall not be modified or any other procedures or connections shall be made. Prepare the control unit by carefully tapping (440F-C4000P) or drilling out (440F-C4 000S, 440FC28013) the cable entry location to be used. The input power supply must be wired separately and enter the control unit through a separate entrance to the power supply used for output wiring. The load t control unit is in its planned position. All wiring of control unit terminals must use the provided conductor type or multi strand conduit cable/switchgear cable/equipment conductor, with the conductor of 0.5-1.5mm2. When the cable enters the control unit (440F-C4000P, 440F-C400S and 440F-C28013), a gland or adapter with IP65 protection must be used. Ensure that the gland or adapter is properly sized and fully tightened. The insulation pins provided must be crimped. This wire and terminal combination avoids the possibility of loose strand short circuit or open circuit caused by excessive tightening or vibration. Make sure to use a suitable ratchet type crimping tool.
