UF C784 AE/3BHE003688R0001工控模块系统备件
接收显式消息的浮点数据
自动化出版物PFLEXRM002DENE2013年8月第1章详细驱动器配置和操作图8读取SLC/PLC5中的浮点显式消息数据图9在SLC/PLC5数字输入中写入浮点显式数据技术信息I/O板上有四个数字输入。其中一个输入专用于启用，无法配置。可以配置其他三个输入。数字输入1为24VDC，数字输入2和3可接受12…24VDC信号。I/O板上有一个24VDC电源，为这些输入供电。数字输入2和3是最大输入频率为350 kHz的高速数字输入。自动化出版物PFLEXRM002DENE2013年8月43详细驱动器配置和操作第1章图10数字输入配置[DigIn 1 Sel]可设置为以下值：826 827位组合828 DigIn1用户数据本地I/O状态（DigIn 1）DigIn1数据DigIn1位838选择器
用户数据本地输入/输出状态详细驱动器配置和操作[DigIn 2 Sel]可设置为以下值：[DigIn 3 Sel]可设为以下值。[DigIn x Debounce]设置延迟时间，以允许数字输入中的任何跳动稳定下来。此参数的范围为0到15.5毫秒。当[DigIn x Sel]设置为“用户选择”时，数字输入的功能由以下因素决定：•[DigIn x Data]决定应永久设置的任何位。详细的驱动器配置和操作第1章•[DigIn x用户数据]将具有与[DigIn x数据]中设置的位相同的位。然后，[Digin x bit]中选择的位将根据数字输入是开还是关进行切换。然后将指定（信宿）参数链接到[Digin x User Data]，以便确定该信宿参数的值。配置示例Digin 1将设置为确定[Speed Ref Sel]的值。DigIn 1将在1“速度参考1”和5“速度参考5”之间切换[Speed Ref Sel]。•[DigIn 1 Sel]=“User Select”•[DigIn 1 Data]=0000 0000 0000 0000 0001•[DigIn1 Bit]=2。这意味着，当我们切换数字输入1时，[DigIn 2 User Data]的第2位将切换。
Receive floating point data for explicit messages
Automation publication PFLEXRM002DENE August 2013 Chapter 1 Detailed Driver Configuration and Operation Figure 8 Reading Floating point Explicit Message Data in SLC/PLC5 Figure 9 Writing Floating point Explicit Data in SLC/PLC5 Digital Input Technical Information There are four digital inputs on the I/O board. One of the inputs is dedicated to enable and cannot be configured. The other three inputs can be configured. Digital input 1 is 24VDC, and digital inputs 2 and 3 can accept 12... 24VDC signals. There is a 24VDC power supply on the I/O board to power these inputs. Digital inputs 2 and 3 are high-speed digital inputs with a maximum input frequency of 350 kHz. Automation publication PFLEXRM002DENE August 43, 2013 Detailed driver configuration and operation Chapter 1 Figure 10 Digital input configuration [DigIn 1 Sel] can be set to the following values: 826 827 bit combination 828 DigIn1 user data local I/O status (DigIn 1) DigIn1 data DigIn1 bit 838 selector
User Data Local I/O Status Detailed Driver Configuration and Operation [DigIn 2 Sel] can be set to the following values: [DigIn 3 Sel] can be set to the following values. [DigIn x Debounce] Set the delay time to allow any jitter in the digital input to stabilize. The range for this parameter is 0 to 15.5 milliseconds. When [DigIn x Sel] is set to "User Selection", the function of digital input is determined by the following factors: • [DigIn x Data] determines any bit that should be permanently set. Detailed Drive Configuration and Operation Chapter 1 • [DigIn x User Data] will have the same bits as those set in [DigIn x Data]. Then, the bit selected in [Digin x bit] will be switched according to whether the digital input is on or off. Then link the specified (sink) parameter to [Digin x User Data] to determine the value of the sink parameter. The configuration example Digin 1 will be set to determine the value of [Speed Ref Sel]. DigIn 1 will switch [Speed Ref Sel] between 1 Speed Ref 1 and 5 Speed Ref 5. • [DigIn 1 Sel]=“User Select”•[DigIn 1 Data]=0000 0000 0000 0000 0001•[DigIn1 Bit]=2。 This means that when we switch digital input 1, the second bit of [DigIn 2 User Data] will switch.
