UFC718AE01 HIEE300936R0001工控备件模块
电流限制参数
开环IT功能和电机电流限制参数路由至最小选择，输入的代数最小值用作电流限制。此外，闭环IT功能可以限制驱动器的电流输出。比较闭环IT函数和转矩电流参考，并将代数最小值用于转矩电流参考。有关开环和闭环IT功能的说明，请参阅第48页的驱动器过载部分。数据链路数据链路用于将I/O数据从通信适配器（如ControlNet（20COMMC）或DeviceNet（20COMMD））传输到控制器。数据链接允许在不使用消息传递的情况下更改参数值。配置数据链路本节包含有关为PowerFlex 700S配置数据链路参数的信息。通信适配器中还有一些参数必须配置为使用Datalink。有关更多信息，请参阅第26页的ControlNet（20COMMC）和第36页的DeviceNet（20COMMD）。
参数是控制器对驱动器的输入
用于写入参数。“数据输入”参数总共可写入8个参数。在700S中，每个参数都是16位整数、32位整数或32位浮点（实数）。这意味着数据链路参数为32位。要写入16位或32位整数参数，该参数必须链接到[Data In x Int]参数之一。要写入实参数，该参数必须链接到[Data In x real]参数之一。示例配置1：使用Datalink写入整数参数：•740[Position Control]链接到707[Data In A1 Int]从控制器发送到[Data In Al Int]的值将显示在[Position Control]中。使用[Data In A1 Int]是因为[Position Control]是整数参数。自动化出版物PFLEXRM002DENE2013年8月35详细驱动器配置和操作第1章示例配置2：使用数据链接写入实参数：•111[Torque Ref 1]链接到708[Data In A1 Real]控制器发送到[Data In Al Real]的值将显示在[Torque Ref]中。使用[Data In A1 Real]是因为[Torque Ref 1]是实整数参数。
Current limit parameters
The open-loop IT function and motor current limit parameters are routed to the minimum selection, and the algebraic minimum value entered is used as the current limit. In addition, the closed-loop IT function can limit the current output of the driver. The closed-loop IT function is compared with the torque current reference, and the algebraic minimum is used for the torque current reference. For a description of open loop and closed loop IT functions, see the Drive Overload section on page 48. Data LinkThe data link is used to transfer I/O data from a communication adapter, such as ControlNet (20COMMC) or DeviceNet (20COMMD), to the controller. Data links allow you to change parameter values without using messaging. This section contains information about configuring data link parameters for the PowerFlex 700S. There are also some parameters in the communication adapter that must be configured to use Datalinks. For more information, see ControlNet (20COMMC) on page 26 and DeviceNet (20COMMD) on page 36.
The parameter is the input of the controller to the driver
Used to write parameters. A total of 8 parameters can be written to the "Data Input" parameter. In 700S, each parameter is a 16 bit integer, a 32-bit integer, or a 32-bit floating point (real number). This means that the data link parameter is 32 bits. To write a 16 bit or 32-bit integer parameter, the parameter must be linked to one of the [Data In x Int] parameters. To write a real parameter, the parameter must be linked to one of the [Data In x real] parameters. Example Configuration 1: Use Datalink to write integer parameters: • 740 [Position Control] link to 707 [Data In A1 Int] The value sent from the controller to [Data In Al Int] will be displayed in [Position Control]. [Data In A1 Int] is used because [Position Control] is an integer parameter. Automation publication PFLEXRM002DENE August 35, 2013 Detailed drive configuration and operation Chapter 1 Example configuration 2: Write real parameters using data link: • 111 [Torque Ref 1] Link to 708 [Data In A1 Real] The value sent by the controller to [Data In Al Real] will be displayed in [Torque Ref]. [Data In A1 Real] is used because [Torque Ref 1] is a real integer parameter.
