UFC760BE141 3BHE004573R0141机器人模块卡件
将计算机安装
DIN导轨上您可以将计算机安装到DIN导轨上。DIN导轨支架安装在计算机背面。DIN导轨支架尺寸见第11页。1.将DIN导轨支架连接到计算机背面（1）。2.使用四个M4 x 5 mm盘头螺钉固定DIN导轨支架；扭矩至0.686 N•m（6.072 lb•in）（2）。重要信息：请勿在高冲击和振动环境中将计算机安装在DIN导轨上。底部10台小型工业非显示计算机背面安装支架自动化出版物6155RIN002EENP2013年7月3。将DIN导轨连接并固定到安装表面（3）。4.将计算机安装在DIN导轨上。a、 将DIN导轨支架的上边缘插入DIN导轨的上边缘。a、 将计算机紧紧地压在DIN导轨（4）的下边缘上。5.拧紧DIN导轨支架上的紧固件，并将其拧紧至1.18 N•m（10.42 lb•in）（5），以固定安装。VESA安装计算机您可以使用提供的VESA安装支架将计算机安装到任何AllenBradley工业显示器或其他表面。该支架符合VESA 100 x 100 mm安装孔模式。VESA安装支架尺寸见第11页。1.将VESA安装支架连接到
安装表面
（1）。2.用四个M4 x 8 mm平头螺钉（2）固定VESA安装支架。3.将计算机放在VESA安装支架（3）上。4.用四个M4 x 8 mm螺钉（4）固定安装。将螺钉拧紧至0.686 N•m（6.072 lb•in）。提示：如果您使用的是现有的DIN导轨，请跳过步骤3。重要信息：如果您将VESA安装到显示器背面、计算机I/O面板必须朝下，显示器必须垂直安装，不得倾斜。紧凑型工业非显示计算机11自动化出版物6155RIN002EENP2013年7月图1安装支架尺寸172（6.77）212（8.346）6（0.236）114.6（4.512）46（1.811）64（2.52）92（3.622）11.3（0.444）140（5.511）150（0.866）100（3.94）156（6.14）100（3.9 4）176.4（6.945）84（3.318）35.85（1.41）2（0.079）DIN导轨安装支架VESA安装支架墙壁安装支架所有尺寸均以mm（in.）为单位12紧凑型工业非显示计算机自动化出版物6155RIN002EENP2013年7月计算机尺寸计算机尺寸以mm（in）为单位。连接外围设备将所需的外围设备（如键盘、鼠标和显示器）连接到计算机上相应的I/O端口。
Install Computer
DIN rail You can mount the computer to a DIN rail. The DIN rail bracket is mounted on the back of the computer. See page 11 for DIN rail bracket dimensions. 1. Connect the DIN rail bracket to the back of the computer (1). 2. Fix the DIN rail bracket with four M4 x 5 mm pan head screws; Torque to 0.686 N • m (6.072 lb • in) (2). IMPORTANT: Do not mount the computer on a DIN rail in high shock and vibration environments. Bottom 10 small industrial non display computers Back mounting bracket Automation publication 6155RIN002EENP July 3, 2013. Attach and secure the DIN rail to the mounting surface (3). 4. Mount the computer on a DIN rail. a. Insert the top edge of the DIN rail bracket into the top edge of the DIN rail. a. Press the computer firmly against the lower edge of the DIN rail (4). 5. Tighten the fasteners on the DIN rail bracket to 1.18 N • m (10.42 lb • in) (5) to secure the installation. VESA Mounting ComputerYou can use the VESA mounting bracket provided to mount the computer to any Allen Bradley industrial display or other surface. The bracket conforms to the VESA 100 x 100 mm mounting hole pattern. See page 11 for VESA mounting bracket dimensions. 1. Connect the VESA mounting bracket to the
Mounting surface
（1）。 2. Secure the VESA mounting bracket with four M4 x 8 mm pan head screws (2). 3. Place the computer on the VESA mounting bracket (3). 4. Fix and install with four M4 x 8 mm screws (4). Tighten the screws to 0.686 N • m (6.072 lb • in). Tip: If you are using an existing DIN rail, skip step 3. Important: If you install VESA on the back of the monitor, the computer I/O panel must face down, and the monitor must be installed vertically without tilting. Compact industrial non display computer 11 Automation publication 6155RIN002EENP July 2013 Figure 1 Mounting bracket size 172 (6.77) 212 (8.346) 6 (0.236) 114.6 (4.512) 46 (1.811) 64 (2.52) 92 (3.622) 11.3 (0.444) 140 (5.511) 150 (0.866) 100 (3.94) 156 (6.14) 100 (3.9 4) 176.4 (6.945) 84 (3.318) 35.85 (1.41) 2 (0.079) DIN rail mounting bracket VESA mounting bracket Wall mounting bracket All dimensions are in mm (in.) 12 Compact industrial non display computer automation publication 6155RIN002EENP Computer dimensions July 2013 Computer dimensions are in mm (in.). Connecting Peripherals Connect the required peripherals, such as the keyboard, mouse, and monitor, to the appropriate I/O ports on the computer.
