USC329AE01 3BHB002483R0001电源模块
中断额定值
编号分断容量赫兹 分断能力 中断 代码‡ 极串联 磁极串联 这些额定值尚未进行认证测试。第有关的信息请参阅下表。编号选择热磁固定热固定磁组装塑壳断路器框架塑壳开关§产品选择框架类别。编号公告塑壳断路器请访问我们的网站：出版物附件报警触点说明名称图框架尺寸类别。编号报警触点 报警触点 触点报警触头 报警接触 触点 辅触点或报警触点 辅触头 报警触点 联系人 触点 报警触点 报警触点 触点 触点 。根据连接方式触点可以用作触点或报警触点。内部电气附件说明页说明页内部电气附件报警触点模块扩展终端操作员个后端子直接旋转操作员相位屏障电机操作员
目录触点
报警触点有多种变体可供客户使用。触点：指示的开关状态。报警触点：指示的跳闸状态。按下塑壳断路器上的测试按钮可启动报警跳闸过电流短路导致跳闸或由于剩余电流分流或欠压释放信号而跳闸。热跳闸触点：仅当检测到过电流短路或保护跳闸时跳闸。型和型框架有一个按钮来测试此功能。仅适用于和帧。这些触点的安装方法是拆除盖并使用卡扣安装装置接近断路器内的右侧口袋。框架配备有猪尾接线每个端子线都有标记。框架和在断路器内部布线并使用针快速连接器进行端接。公告塑壳断路器请访问我们的网站：出版物附件图 公告型塑壳断路器断路器请访问我们的网站：出版物配件并联跳闸允许通过向并联跳闸线圈施加控制电压来远程跳闸。框架和配有清管器尾部接线每个端子线都有标记。
Interruption rating
No. Breaking capacity Hz Breaking capacity Interrupting code ‡ Pole series pole series These ratings have not been certified. Refer to the following table for information on section. Select thermal magnetic fixed thermal fixed magnetic assembly molded case circuit breaker frame molded case switch § Product selection frame category. No. Bulletin Molded Case Circuit Breaker Please visit our website: publication attachment Alarm contact description Name diagram Frame size category. No. Alarm contact Alarm contact Alarm contact Alarm contact Alarm contact Auxiliary contact or Alarm contact Auxiliary contact Alarm contact Alarm contact Alarm contact Alarm contact Contact. The contact can be used as contact or alarm contact according to the connection mode. Internal Electrical Accessories Description Page Description Page Internal Electrical Accessories Alarm Contact Module Extension Terminal Operator Rear Terminals Direct Rotation Operator Phase Barrier Motor Operator
Catalog Contact
There are many variants of alarm contacts available for customer use. Contact: indicates the switch status. Alarm contact: indicates the tripping state. Press the test button on the molded case circuit breaker to start the alarm tripping, tripping caused by overcurrent short circuit or tripping due to residual current shunt or undervoltage release signal. Thermal trip contact: trip only when overcurrent short circuit or protection trip is detected. Type and type frames have a button to test this function. Applies only to and frames. The installation method of these contacts is to remove the cover and use the snap mounting device to access the right pocket in the circuit breaker. The frame is equipped with pigtail wiring. Each terminal wire is marked. The frame and are wired inside the circuit breaker and terminated using pin quick connectors. Bulletin Molded Case Circuit Breakers Please visit our website: publication attachment figure Bulletin Molded Case Circuit Breaker Please visit our website: publication accessory shunt tripping allows remote tripping by applying control voltage to the shunt tripping coil. Each terminal line of the frame and the tail wire with pig is marked.
