VMIPCI-5661工控模块机器人备件
安装螺母
电缆0各方向调整附件直角支架#0旋转/倾斜支架#09..8..0.08.0.90.注意事项。如果8mm锁紧螺母上的扭矩超过0 inlb，则可能会损坏传感器外壳。可选安装套件0配有两个000、一个0090锁紧螺母、内齿星形垫圈和用于通孔安装的螺钉/螺母。配置Sensor All ClearSight RightSight型号时，顶盖上有一个单圈调节旋钮。该旋钮控制传感器对反射器反射回的光的灵敏度。出厂默认设置为最大灵敏度。目视对准反射器上的传感器，直到黄色输出LED亮起亮操作模式或熄灭暗操作模式。还要验证橙色边缘LED是否亮起。为了确保光束居中，需要在水平和垂直平面上扫描传感器，并确定输出指示器在哪个位置亮起然后熄灭。将传感器设置在两个位置之间的中间位置。
传感器
可见红色光束将在反射器上可见，并可用作对准辅助。用要检测的物体断开光束，并检查输出指示灯是否打开暗操作模式。如果没有出现这种情况，请调低灵敏度调整，直到出现这种情况。通过移除物体恢复光束，并检查指示器是否再次关闭，橙色边缘LED是否亮起。如果没有出现这种情况，请增大反射器的尺寸或减小反射器与传感器之间的距离。在某些情况下可能需要将传感器和反射器稍微倾斜到目标中，以最小化传感器输出的错误触发。根据要感测的透明物体的类型，可能需要具有同轴光学器件的传感器。配件说明目录号安装套件0夹具式支架8ABP8嵌入式安装适配器090现场安装端子室引脚DC Micro 8ATSDM跳线m.ft，引脚DC Micro889DFAC跳线m/ft，引脚AC Micro 889RFAEA反射器。
Mounting nut
Cable 0 adjustment accessories in all directions Right angle bracket # 0 Rotation/tilt bracket # 09.. 8.. 0.08.0.90. Precautions. If the torque on the 8mm locknut exceeds 0 inlb, damage to the sensor housing may occur. The optional installation kit 0 is equipped with two 000, one 0090 lock nut, internal tooth star washer and screw/nut for through hole installation. When configuring the Sensor All ClearSight RightSight model, there is a single turn adjustment knob on the top cover. This knob controls the sensitivity of the sensor to the light reflected back by the reflector. The factory default setting is maximum sensitivity. Visually align the sensor on the reflector until the yellow output LED lights up the operating mode or turns off the dark operating mode. Also verify that the orange edge LED is lit. To ensure that the beam is centered, scan the sensor in the horizontal and vertical planes and determine where the output indicator lights up and then turns off. Set the sensor midway between the two positions.
sensor
The visible red beam will be visible on the reflector and can be used as an alignment aid. Disconnect the beam with the object to be detected, and check whether the output indicator turns on the dark operation mode. If this does not happen, turn down the sensitivity adjustment until this happens. Restore the beam by removing the object and check that the indicator turns off again and that the orange edge LED lights up. If this does not happen, increase the size of the reflector or reduce the distance between the reflector and the sensor. In some cases, it may be necessary to tilt the sensor and reflector slightly into the target to minimize false triggering of the sensor output. Depending on the type of transparent object to be sensed, a sensor with coaxial optics may be required. Description of accessories Catalog No. Installation kit 0 Clamp type bracket 8ABP8 embedded installation adapter 090 Field installation terminal room pin DC Micro 8ATSDM jumper m Ft, pin DC Micro889DFAC jumper m/ft, pin AC Micro 889RFAEA reflector.
