VMIVME-3115工控模块控制器
电源输入
换向分解器或高分辨率输出2.8（0.11）检查孔（4），顶部和底部1/16至27 NPT插头，直径10 mm。直径115 mm的通孔4需要。B、 C.（直径为0.394，在直径为4.528的BC上）安装螺栓必须为帽头式M6 x 1.0螺纹孔16（0.63），最小深度6.07/5.99（0.239/0.236）15.49/15.24（0.610/0.600）轴详图30.7（1.21）全深度端铣键槽1电机前端钟形角半径22.22（0.875）最大轴跳动0.04（0.0016）T.I.R轴端隙0.127（0.005）最大导向偏心0.08（0.0032）T.I.L最大端面跳动0.08（0.0032）T.I.R铭牌详图轴和导向公差高分辨率电机端部1法兰安装（单位：毫米和（英寸）反馈目录编号描述AD AG C键端铣键槽（全深度）无制动器
制动器
（IP67等级），AD、AG和C增加45 mm（1.75 in.）。尺寸符合NEMA标准MG 7-2.4.1.3和IEC 72-1。轴公差符合DIN 42955，“N”公差。1326AB 460V，扭矩增强系列，交流伺服电机19出版物 扭矩增强系列（分解器和高分辨率反馈）AD AG C 50（1.97）键45 45 163.6最大值（6.44）25.4（1.00）25.4（1.00）25.4（1.00）130.014/129.989直径。（5.1186/5.1176直径）24.009/23.996直径。（0.9452/0.9447）3.5（0.138）15.0（0.59）9.52/9.50直径。（0.3750/0.3745直径）130.20/30.15直径。（5.126/5.24直径）功率输入2.0（0.079）8.08/8.00（0.318/0.315）19.99/19.74（0.787/0.777）轴详图12 mm直径。165 mm直径上需要通孔4。B、 C.（6.496直径B.C.上的0.472直径）安装螺栓必须为帽头式检查孔（4），顶部和底部1/16至27 NPT堵头M8 x 1.25螺纹孔19（0.75）深最小41（1.61）
Power input
Reversing resolver or high-resolution output 2.8 (0.11) inspection hole (4), top and bottom 1/16 to 27 NPT plugs, 10 mm diameter. Required for 115 mm diameter through hole 4. B. C. (0.394 diameter, on BC with 4.528 diameter) The mounting bolt must be a cap type M6 x 1.0 threaded hole 16 (0.63), Minimum depth 6.07/5.99 (0.239/0.236) 15.49/15.24 (0.610/0.600) shaft detail 30.7 (1.21) full depth end milling keyway 1 motor front end bell angle radius 22.22 (0.875) maximum shaft runout 0.04 (0.0016) T.I.R shaft end clearance 0.127 (0.005) maximum guide eccentricity 0.08 (0.0032) T.I.L maximum face runout 0.08 (0.0032) T.I.R nameplate detail shaft and guide tolerance high resolution motor end 1 flange installation (unit: mm and (inch) Feedback catalog number description AD AG C key end milling keyway (full depth) without brake
Brake
(IP67 grade), AD, AG and C increase by 45 mm (1.75 in.). Dimensions conform to NEMA standard MG 7-2.4.1.3 and IEC 72-1. Shaft tolerance according to DIN 42955, "N" tolerance. 1326AB 460V, torque enhancement series, AC servo motor 19 Publication torque enhancement series (resolver and high-resolution feedback) AD AG C 50 (1.97) key 45 45 163.6 maximum value (6.44) 25.4 (1.00) 25.4 (1.00) 25.4 (1.00) 130.014/129.989 diameter. (5.1186/5.1176 dia.) 24.009/23.996 dia. (0.9452/0.9447) 3.5 (0.138) 15.0 (0.59) 9.52/9.50 diameter. (0.3750/0.3745 diameter) 130.20/30.15 diameter. (5.126/5.24 diameter) power input 2.0 (0.079) 8.08/8.00 (0.318/0.315) 19.99/19.74 (0.787/0.777) shaft detail 12 mm diameter. A through-hole 4 is required on a 165 mm diameter. B. C. (0.472 diameter on 6.496 diameter B.C.) The mounting bolt must be a cap type inspection hole (4), 1/16 to 27 NPT plug M8 x 1.25 threaded hole 19 (0.75) at the top and bottom with a minimum depth of 41 (1.61)
