WOODWARD 9907-166工控模块机器人备件
警告：
必须重新安装CF卡锁紧螺钉，以振动要求满足危险位置、机械冲击和振动要求。F C E A B D显示计算机显示危险场所的工业计算机29自动化出版物6181X-IN001D-EN-P-2015年7月12日。拧紧固定驱动器托架槽盖的螺钉（L）。13.按照第24页的后期配置步骤。在底部CF卡插槽中安装卡按照这些步骤在底部CF卡插槽中安装CF卡。1.拧松固定CF卡插槽盖的螺钉（A）。2.打开CF卡插槽盖（B）。如有必要，按下铰链侧的按钮，取出插入的卡。3.将新的CF卡插入插槽，直到其牢固就位（C）。4.关闭CF卡插槽盖（D）。警告：所有计算机型号底部的CF卡插槽都可以热插拔，但只能位于非危险位置。您可以在计算机运行时从该插槽插入或取出卡。当计算机在危险位置使用时，除非电源已关闭，否则不要在底部CF卡插槽中插入或取出卡。
正确安装
注意：正确安装后，在遇到阻力之前，超过80%的CF卡很容易插入插槽。如果您很快遇到阻力，请取出卡，将其旋转180°，然后重新插入。不要强行将卡插入插槽，否则会损坏连接器引脚。G J H L K I显示计算机显示用于危险场所的30台工业计算机自动化出版物6181X-IN001D-EN-P-2015年7月5.拧紧CF卡槽盖螺钉（E）。安装插件卡按照以下步骤安装插件卡。1.断开计算机的电源。2.从计算机上卸下后盖。有关详细信息，请参阅第25页的“拆下封面”说明。3.拧下固定槽盖的一个螺钉。不要丢弃螺钉。4.拆下槽盖并将其存放起来，以便稍后重新组装。5.握住扩充卡的边缘，将其从保护包装中取出。6.将扩充卡连接到兼容的转接板插槽。验证卡是否正确安装在插槽中。7.用插槽盖上的螺钉固定扩充卡。
Warning:
The CF card locking screws must be reinstalled to meet the vibration requirements for hazardous locations, mechanical shock and vibration. F C E A B D Display Computer Display Industrial Computer in Hazardous Locations 29 Automation Publication 6181X-IN001D-EN-P-2015, July 12. Tighten the screws (L) that secure the drive bay slot cover. 13. Follow the post configuration steps on page 24. Installing a card in the bottom CF card slot Follow these steps to install a CF card in the bottom CF card slot. 1. Loosen the screw (A) that secures the CF card slot cover. 2. Open the CF card slot cover (B). If necessary, press the button on the hinge side to remove the inserted card. 3. Insert the new CF card into the slot until it is firmly seated (C). 4. Close the CF card slot cover (D). Warning: The CF card slot on the bottom of all computer models can be hot swapped, but can only be located in a non hazardous location. You can insert or remove a card from this slot while the computer is running. When the computer is used in a dangerous location, do not insert or remove a card from the bottom CF card slot unless the power is turned off.
Correct installation
Note: After correct installation, more than 80% of CF cards can easily be inserted into the slot before encountering resistance. If you soon encounter resistance, remove the card, rotate it 180 °, and then reinsert it. Do not force the card into the slot, or the connector pins will be damaged. G J H L K I display computer shows 30 industrial computers used in hazardous areas Automation publication 6181X-IN001D-EN-P-2015 July 5. Tighten CF card slot cover screws (E). To install the plug-in card, follow the steps below to install the plug-in card. 1. Disconnect the power of the computer. 2. Remove the back cover from the computer. For details, refer to the instructions "Removing the Cover" on page 25. 3. Unscrew one screw fixing the slot cover. Do not discard the screws. 4. Remove the tank cover and store it for later reassembly. 5. Hold the expansion card by its edges and remove it from the protective package. 6. Connect the expansion card to a compatible docking station slot. Verify that the card is properly installed in the slot. 7. Secure the expansion card with the screws on the slot cover.
