WR-D4001工控模块系统备件
注意事项：
采取预防措施，防止金属碎屑进入已安装在面板中的组件，以避免人身伤害或损坏面板组件。注意：将夹子拧紧到规定的扭矩，以提供适当的密封，并有助于防止损坏计算机。自动化公司对因安装不当而对外壳内的计算机或其他设备造成的水或化学损坏不承担任何责任。5 4 3 6 9 1 10 827用于危险场所的手动拧紧和扭矩顺序工业计算机17自动化出版物6181X-IN001D-EN-P-2015年7月将非显示计算机安装在墙上使用提供的四个螺钉将非显示电脑固定到金属墙上，如外壳或设备室中的钢板。按照以下步骤安装非-显示计算机。1.确认电源已断开。2.决定在哪里安装计算机后，在墙上钻孔以容纳四个M4盘头螺钉。图示显示了安装孔位置，尺寸单位为mm（in.）。3.将提供的两个带垫圈的螺钉连接到位置1和2。4.将计算机安装到墙上。5.将剩余的两个带垫圈的螺钉连接到位置3和4。6.拧紧至适合螺钉和壁材料的扭矩。建议的钢制扭矩为1.13…1.36 N•m（10…12 lb•in）。
重要信息：
请勿将非显示计算机安装在水平表面上。335.3（13.2）190.5（7.5）3 4 1 2 18用于危险场所的工业计算机自动化出版物6181X-IN001D-EN-P-2015年7月硬件功能插图显示了用于危险场所工业计算机的硬件功能。项目组件项目组件1 LCD面板（仅在显示型号上）7 PCI转接板插槽盖2 CompactFlash II型卡插槽（右侧）8电源开关3后盖9 DC输入端子块4串行COM端口（RS-232），2 10功能接地螺钉5 1 GB LAN端口（RJ45），2 11铰链门，覆盖4个USB端口6个DVI-I端口12个CompactFlash II型卡插槽（底部）1）USB端口和底部CF卡插槽可热插拔，但仅在非危险位置。有关正确使用这些端口的更多信息，请参阅第4页的危险位置。1 3 2 4 56 7 12 11 10 9 8危险位置的工业计算机19自动化出版物6181X-IN001D-EN-P-2015年7月连接外围设备下图显示了计算机的I/O端口面板。与每个端口兼容的外围组件如下图所示。
matters needing attention:
Take precautions to prevent metal debris from entering components that have been installed in the panel to avoid personal injury or damage to the panel assembly. NOTE: Tighten the clips to the specified torque to provide a proper seal and help prevent damage to the computer. Automation Company shall not be responsible for water or chemical damage to computers or other equipment inside the enclosure due to improper installation. 5 4 3 6 9 1 10 827 Manual tightening and torque sequence for hazardous locations Industrial computer 17 Automation publication 6181X-IN001D-EN-P-2015 July Install the non display computer on the wall Use the four screws provided to fix the non display computer on the metal wall, such as the steel plate in the enclosure or equipment room. Follow these steps to install a non display computer. 1. Confirm that the power supply is disconnected. 2. After deciding where to install the computer, drill holes in the wall to accommodate four M4 pan head screws. The figure shows the location of the mounting hole, and the dimensions are in mm (in.). 3. Attach the two screws provided with washers to positions 1 and 2. 4. Mount the computer on the wall. 5. Connect the remaining two screws with washers to positions 3 and 4. 6. Tighten to a torque suitable for the screw and wall material. The recommended steel torque is 1.13... 1.36 N • m (10... 12 lb • in).
Important information:
Do not install a non display computer on a horizontal surface. 335.3 (13.2) 190.5 (7.5) 3 4 1 2 18 Industrial computer automation publication for hazardous locations 6181X-IN001D-EN-P-2015 July hardware function illustration shows the hardware functions of industrial computers for hazardous locations. Item componentItem componentItem componentItem component1 LCD panel (only on the display model) 7 PCI adapter board slot cover 2 CompactFlash II card slot (right side) 8 Power switch 3 Rear cover 9 DC input terminal block 4 Serial COM port (RS-232), 2 10 Function grounding screw 5 1 GB LAN port (RJ45), 2 11 Hinged door, covering 4 USB ports 6 DVI-I ports 12 CompactFlash II card slots (bottom) 1) USB port and bottom CF card slot can be hot swapped, But only in non hazardous locations. For more information on using these ports correctly, see Hazardous Locations on page 4. 1 3 4 56 7 12 11 10 9 Industrial computers in hazardous locations 19 Automation publication 6181X-IN001D-EN-P-2015 July Connecting peripherals The following figure shows the I/O port panel of the computer. Peripheral components compatible with each port are shown in the figure below.
