XV-430-12TSB-1-10自动化模块备件
有关详细信息
控制多达个有关详细信息，请参见序列器控制锁存旁路部分按照模式定义，用户必须用感兴趣的模式填充寄存器至寄存器中的状态位任何状态都可以指向任何模式，但状态始终指向模式请注意，定序器按顺序移动状态，直到状态机深度定义状态后，用户必须通过更改位（寄存器，位）来设置定序器要使用的状态数为索引因此，将深度设置为会使（寄存器，位）成为循环中的唯一状态传输状态机编程后，操作由（传输复位，引脚）和（传输提前，引脚）引脚控制或者，可以使用和位（分别为寄存器、位和位）通过控制操作将传输状态机上的指针移动到状态，而不管指针的当前位置如何，并且可以在任何时候断言状态始终引用模式
不能设置为其他模式然而
模式可被任何变送器配置覆盖模式在寄存器和寄存器中定义脉冲使发射机状态机指针一次前进一个状态，直到循环通过定义的定序器深度此时，附加的脉冲将指针移回状态状态应用位（寄存器，位）中定义的模式单通道频率扫描图显示了可在通道的至频率扫描期间使用的操作方法根据表，在到扫描期间需要三个倍增器滤波器状态在本例中，定义的状态机深度（寄存器，位）为，因为循环中有四个状态，为索引如图所示，•乘法器滤波器状态=睡眠（环路外）•乘法滤波器状态=中频乘法器就绪•乘法器滤波器状态=向输出至•乘法员滤波器状态=向输入至•乘滤波器状态=向的输出至初始状态为睡眠状态，功耗最低通过脉冲引脚达到该状态然后，上的脉冲将状态机推进到环路内的一状态
For more information
Control up to. For details, see the Sequencer Control Latch Bypass section. According to the mode definition, the user must fill the register with the mode of interest to the status bit in the register. Any state can point to any mode, but the state always points to the mode. Note that the sequencer moves the state in order until the state machine deeply defines the state, The user must set the number of states to be used by the sequencer as an index by changing the bit (register, bit). Therefore, setting the depth to make (register, bit) the only state in the cycle. After programming the transmission state machine, the operation is controlled by (transmission reset, pin) and (transmission advance, pin) pins or, The and bits (register, bit and bit respectively) can be used to move the pointer on the transmission state machine to the state through control operation, regardless of the current position of the pointer, and the state can always reference the mode at any time
It cannot be set to other modes
Mode can be configured by any transmitter Override mode Define pulses in registers and registers to advance the transmitter state machine pointer one state at a time until the loop passes through the defined sequencer depth At this time, additional pulses move the pointer back to the mode defined in the state state application bit (register, bit) Single channel frequency scanning diagram shows the operation methods that can be used during the channel to frequency scanning According to the table, Three multiplier filter states are required during scanning to. In this example, the defined state machine depth (register, bit) is, because there are four states in the loop, which are indexed as shown in the figure, • Multiplier filter state=sleep (outside the loop) • Multiplier filter state=IF multiplier ready • Multiplier filter state=output to • Multiplier filter state=input to • Multiplier filter state
