XVC770BE101 3BHE021083R0101工控备件
切换频率使用就绪模式
数据表参数测试条件注释最小类型最大单元切换时间倍增带休眠到激活倍增带切换使用就绪模式休眠到激活通道切换使用就绪模式，数字输入逻辑电平逻辑低.逻辑高.数字输出逻辑电平逻辑高.逻辑高..输出.电源模拟电源电压范围（、、、）...电流消耗一通道激活芯片禁用功耗一通道激活芯片禁用数字电源电压范围（）..电流消耗芯片启用µ功耗芯片启用µ数据表版|，共计时规范除非另有说明。表.时序参数描述测试条件注释最小类型最大单元最大时钟速率仅写入写入和读取最小脉冲宽度高最小脉冲宽度低设置时间数据有效设置时间上升时间输出加载下降时间输出加载，%-%时序图不在乎不在乎不在乎不在乎指令周期数据传输周期-图。事务结构（优先）不关心写入写入时序图不关心读取不关心。
模式数据
读取时序图块写入模式数据可以使用块写入模式写入寄存器，其中寄存器地址自动递增，连续寄存器的数据可以在不发送新地址位的情况下写入。数据写入可以无限期地继续，直到引发，结束事务。参见图不关心写入不关心一寄存器地址一寄存器数据（+一寄存器）数据-图.块写入数据表版|，共绝对最大额定值表.参数额定值引脚连接的公共接地。绝对最大额定值下列出的应力或以上的应力可能会对产品造成永久性损坏。这只是压力等级；不暗示产品在本规范操作部分所述的这些或任何其他条件下的功能操作。长时间超过最大操作条件的操作可能会影响产品的可靠性。耐热性热性能与印刷电路板（）设计和操作环境直接相关。需要仔细注意热设计。θ是在一立方英尺密封外壳中测量的与环境热阻的自然对流结。
Switch frequency to use ready mode
Data Table Parameter Test Condition Notes Minimum Type Maximum Unit Switching Time Multiplier with Sleep to Active Multiplier with Switch Using Ready Mode Sleep to Active Channel Switch Using Ready Mode, Digital input logic level logic low. Logic high. Digital output logic level logic high. Logic high.. Output. Power supply Analog power supply voltage range (,,,)... Current consumption One channel activation chip disables power consumption One channel activation chip disables digital power supply voltage range ().. Current consumption chip enables µ power consumption chip enables µ data table version |, unless otherwise specified. Table. Description of timing parameters Test conditions Note Minimum type Maximum unit Maximum clock rate Write write and read only Minimum pulse width High Minimum pulse width Low Set time Data Valid Set time Rise time Output load Drop time Output load% -. The transaction structure (priority) does not care about the write write sequence diagram does not care about the read.
Mode data
Reading timing chart block write mode data can be written to registers using block write mode, where the register address is automatically incremented, and the data of continuous registers can be written without sending new address bits. Data writing can continue indefinitely until the transaction is raised and ended. Refer to the figure Do not care about writing a register address Do not care about a register data (+a register) - Figure. Block write data table version |, total absolute maximum ratings table. Common grounding of parameter rating pin connection. Stresses listed below or above the absolute maximum rating may cause permanent damage to the product. This is just the pressure level; It does not imply the functional operation of the product under these or any other conditions described in the operation section of this specification. Operation beyond the maximum operating conditions for a long time may affect the reliability of the product. The thermal performance of heat resistance is directly related to the design and operating environment of printed circuit board (PCB). Careful attention needs to be paid to thermal design. θ It is a natural convection junction with the thermal resistance of the environment measured in a cubic foot sealed enclosure.
