YM322001-ED模块控制器
工厂设置：
简介1-1第1章简介SD3100直流电源模块将固定电压和频率的三相交流电源转换为可调电压的直流电源，可用于为直流电机的电枢或磁场供电。SD3100电源模块在AutoMax分布式电源系统（DPS）环境中运行，并由AutoMax编程执行软件控制。电源模块通过内部安装的电源模块接口（PMI）机架与AutoMax系统通信，该机架包含驱动器的控制电路并执行电机控制算法。SD3100配置可控制直流电机，额定功率为700至2500 HP，额定电流为1250、1650和3000A。可提供460、575和660 VAC的输入电压。图1.1显示了SD3100目录编号方案。
门扇过滤器
输入电压HP单元配置机柜选项分布式电源3 4系统驱动器号3。3000A模块不提供非再生单元。2.单元可容纳顶部入口和底部出口。底部入口需要额外的部分。2.4.在此处添加选项代码。用破折号分隔选项代码。顶部出口需要单独的附加部分。1.需要单独订购、单独安装的7.5至25kVA现场隔离变压器。参见第1.1.4-4节SD3100电源模块3同步丢失故障避免警告（第3位）系统在交流线路电压暂时丢失的情况下继续运行。如果交流线路电压丢失超过2秒，系统将立即进入空闲状态，并在寄存器202/1202中设置第3位（交流线路同步故障）。4电流参考限制警告（第4位）电流参考已超过作为最大电流限制配置参数输入的值。
Factory settings:
Introduction 1-1 Chapter 1 Introduction SD3100 DC power module converts three-phase AC power supply with fixed voltage and frequency into DC power supply with adjustable voltage, which can be used to supply power to armature or magnetic field of DC motor. The SD3100 power module operates in an AutoMax Distributed Power System (DPS) environment and is programmed by AutoMax to perform software control. The power module communicates with the AutoMax system through an internally mounted power module interface (PMI) rack that contains the driver's control circuit and executes motor control algorithms. The SD3100 is configured with a controllable DC motor with a rated power of 700 to 2500 HP and a rated current of 1250, 1650 and 3000A. Input voltages of 460, 575 and 660 VAC are available. Figure 1.1 shows the SD3100 catalog numbering scheme.
Door leaf filter
Input Voltage HP Unit Configuration Enclosure Options Distributed Power Supply 3 4 System Drive Letter 3. The 3000A module does not provide a non regenerative unit. 2. The unit can accommodate the top inlet and bottom outlet. An additional section is required for the bottom entrance. 2.4. Add option codes here. Separate option codes with dashes. A separate additional section is required for the top outlet. 1. 7.5 to 25kVA field isolation transformers that need to be ordered and installed separately. Refer to Section 1.1.4-4 SD3100 Power Module 3 Synchronization Loss Failure Avoidance Warning (Bit 3). The system will continue to operate when the AC line voltage is temporarily lost. If the AC line voltage is lost for more than 2 seconds, the system will immediately enter the idle state and set bit 3 (AC line synchronization fault) in register 202/1202. 4 Current reference limit warning (bit 4) The current reference has exceeded the value entered as the maximum current limit configuration parameter.
