YM322001-EX工控备件机器人模块
窗口功能：
窗口高切换输出（2或1）0SET偏移调整（量程的3%）RP1/RP2滞后功能；复位点切换输出；低，高=最小，最大压力值OFF=显示关闭；SP1/FH1=功能开关点1，RP1/FL1=功能重置点1，SP2/FH2=功能切换点2，RP2/FL2=功能重置点2 FL1/FL2窗口功能：窗口低开关输出（1或2）EF扩展编程功能RES将设置参数返回出厂设置DS1/DS2开关延迟时间，必须在任何电信号变化发生前不中断地发生（SP1或SP2）DISU显示更新1、2、5、10更新/秒DISR将显示指示器旋转180°DR1/DR2开关延迟时间，必须在任何电信号变化发生之前不中断地出现（RP1或RP2）RHL清除最小值和最大值存储器PAS密码输入，0000=无密码密码逐位输入OU1开关功能开关输出OU2 HNO=滞后功能，常开HNC=滞后功能、常闭FNO=窗口功能、常开FNC=窗口功能，常闭标签输入16位字母数字测量点编号状态切换输出
状态切换输出
显示模式•短按显示装置•长按显示设定参数编程模式•短按下菜单向上参数值（逐步）•长按菜单向上参数值（快速）显示模式•装置•长按进入编程模式编程模式•短按菜单向上参数值向上（逐步）•长按菜单向下参数值向下（快速）显示模式•短键显示装置四位LED显示屏•显示压力值•显示菜单项•显示参数编程模式•长按选择菜单项确认输入注：压力开关有两种操作模式，显示模式和编程模式。按键的功能取决于所选的操作模式。回车键：在编程模式下，按回车键一次以设置选定参数的值。注：短按等于三秒；长按等于5秒。罗克韦尔自动化出版物836P-IN001B-EN-P-2017年12月7显示带IO链接菜单的固态压力开关（编程和工厂设置）显示模式按下菜单键5秒编程模式（要设置值，请按enter）
Window function:
Window high switching output (2 or 1) 0SET offset adjustment (3% of the range) RP1/RP2 hysteresis function; Reset point switching output; Low, high=minimum, maximum pressure value OFF=display off; SP1/FH1=function switch point 1, RP1/FL1=function reset point 1, SP2/FH2=function switch point 2, RP2/FL2=function reset point 2 FL1/FL2 window function: window low switch output (1 or 2) EF extended programming function RES will return the setting parameters to the factory setting DS1/DS2 switch delay time, It must occur uninterruptedly (SP1 or SP2) before any electrical signal change. DISU display updates 1, 2, 5 and 10 updates/sec. DISR rotates the display indicator by 180 °. DR1/DR2 switch delay time must occur uninterruptedly (RP1 or RP2) before any electrical signal change. RHL clears minimum and maximum values. PAS password input. 0000=no password password bit by bit input. OU1 switch function switch output. OU2 HNO=lag function, Normally open HNC=hysteresis function, normally closed FNO=window function, normally open FNC=window function, normally closed label input 16 alphanumeric measurement point number status switching output
State switching output
Display mode • Short press of display device • Long press of display setting parameter programming mode • Short press of menu up parameter value (step by step) • Long press of menu up parameter value (fast) display mode • Device • Long press to enter programming mode programming mode • Short press of menu up parameter value up (step by step) • Long press of menu down parameter value down (fast) Display mode • Four digit LED display screen of short key display device • Display pressure value • Display menu item • Display parameter programming mode • Long press to select menu item to confirm input Note: There are two operation modes of pressure switch, display mode and programming mode. The function of the keys depends on the selected operating mode. Enter: In programming mode, press Enter once to set the value of the selected parameter. Note: Short press equals to three seconds; Long press equals 5 seconds. Rockwell Automation Publication 836P-IN001B-EN-P-2017 December 7 Display of solid state pressure switch (programming and factory setting) display mode with IO link menu Press the menu key for 5 seconds to program the mode (to set the value, press enter)
