YPM102E工控备件机器人模块
标称位置工艺连接
非线性≤ 量程的±0.5%（BFSL，IEC 61298-2）长期漂移≤ 量程的±0.2%（IEC 61298-2）开关输出开关点精度：≤ 量程的±1%；
调整精度：≤ 量程显示的±0.5%≤ 速率温度范围内的±1.0%量程±1位温度误差典型值：≤ 量程的±1.0%；最大值：≤ 额定温度范围内量程温度系数的±2.5%平均TC零点：≤ 量程的±0.2%/10 K（典型值）；平均TC跨度：≤ 量程的±0.1%/10 K（典型）参考操作条件工作温度15…25°C（59…77°F）大气压力950…1050 mbar（13.78…15.23 psi）湿度45…75%r.h.标称位置工艺连接下部安装（LM）电气安全短路保护4…20 mA，输出1/输出2 vs.V反向极性保护V+vs。V绝缘电压500V DC过压保护40V DC罗克韦尔自动化出版物836P-IN001B-EN-P-2017年12月3显示固态压力开关，IO链路1/4英寸。
内螺纹尺寸[mm（in.）]接线图匹配电缆目录号889D–F4AC-2（M12x1连接器）目录号888D-R4AC-2（M12x1直角连接器）工艺连接规范（续）材料接液部件工艺连接不锈钢316 L压力传感元件<9.8 bar（142 psi）：不锈钢316≥ 9.8 bar（42 psi）：不锈钢13-8 PH非润湿部件外壳不锈钢304键盘TPE-E显示窗聚碳酸酯显示头聚碳酸酯和ABS工艺连接螺纹1/4 in。NPT外螺纹1/4英寸。NPT内螺纹G 1/4英寸。BSPP外螺纹G 1/4英寸。BSPP内螺纹G 1/2英寸。B Blush IO链路规范IO链路协议：最小周期时间：速率：过程数据长度：数据存储支持：版本1.1 3 ms COM2（38.4 k Baud）16位（帧2.2）是38（1.5）直径。36（1.42）72 92.3（2.83）（3.63）45（1.77）35（1.38）直径。
重要IO链路操作
重量约220 g（7.76 oz）重要IO链路操作仅在连接到IOLink主机（如1734-4IOL或任何竞争性IO链路主机）时可用。在标准IO模式（SIO）下，传感器作为离散PNP输出工作。属性描述测量单元压阻测量单元和金属测量隔膜应用测量和监控绝对压力和表压过程连接螺纹− 1/4英寸。NPT内螺纹− 1/4英寸。NPT外螺纹罗克韦尔自动化出版物显示带IO链路调试的固态压力开关进行机械连接•对于齐平安装连接选项，在安装前不久，不要拆除保护帽。安装期间，确认隔膜未损坏。•安装时，确保仪器的密封面清洁无损坏。•只能通过扳手拧入或拧下仪器。切勿将外壳用作工作面。•正确的扭矩取决于工艺连接的尺寸和使用的垫片（形式/材料）。•拧入时，小心不要穿过螺纹。
Nominal position process connection
Nonlinear ≤ ± 0.5% of the range (BFSL, IEC 61298-2) Long term drift ≤ ± 0.2% of the range (IEC 61298-2) Switch output switching point accuracy: ≤ ± 1% of the range;
Adjustment accuracy: ≤ ± 0.5% of the range display ≤ ± 1.0% of the range within the speed temperature range ± 1-bit temperature error typical value: ≤ ± 1.0% of the range; Maximum value: ≤ ± 2.5% of the range temperature coefficient within the rated temperature range Average TC zero point: ≤ ± 0.2% of the range/10 K (typical value); Average TC span: ≤ ± 0.1% of the range/10 K (typical) Reference operating conditions Operating temperature 15... 25 ° C (59... 77 ° F) Atmospheric pressure 950... 1050 mbar (13.78... 15.23 psi) Humidity 45... 75% r.h. Nominal position Process connection Lower mount (LM) Electrical safety Short circuit protection 4... 20 mA, Output 1/Output 2 vs.V Reverse polarity protection V+vs. V insulation voltage 500V DC overvoltage protection 40V DC Rockwell Automation Publication 836P-IN001B-EN-P-2017 December 3, solid state pressure switch, IO link 1/4 inch.
Internal thread size [mm (in ）]Wiring diagram matching cable catalog number 889D – F4AC-2 (M12x1 connector) catalog number 888D-R4AC-2 (M12x1 right angle connector) process connection specification (continued) material wetted part process connection stainless steel 316 L pressure sensor element<9.8 bar (142 psi): stainless steel 316 ≥ 9.8 bar (42 psi): stainless steel 13-8 PH non wetting part shell stainless steel 304 keyboard TPE-E display window polycarbonate display head polycarbonate and ABS process connection thread 1/4 inch. NPT male 1/4 inch. NPT female G 1/4 inch. BSPP external thread G 1/4 inch. BSPP female thread G 1/2 inch. B Blush IO link specification IO link protocol: minimum cycle time: rate: process data length: data storage support: version 1.1 3 ms COM2 (38.4 k Baud) 16 bits (frame 2.2) is 38 (1.5) in diameter. 36 (1.42) 72 92.3 (2.83) (3.63) 45 (1.77) 35 (1.38) dia.
Important IO link operation
Weighing approximately 220 g (7.76 oz), critical IO link operations are available only when connected to an IOLink host (such as a 1734-4IOL or any competitive IO link host). In standard IO mode (SIO), the sensor operates as a discrete PNP output. Attribute Description Measurement Unit Piezoresistive measurement unit and metal measurement diaphragm applications Measure and monitor absolute pressure and gauge pressure process Connection threads − 1/4 inch. NPT female − 1/4 inch. NPT male Rockwell Automation publications show that solid state pressure switches with IO link commissioning are mechanically connected • For flush mounting connection options, do not remove the protective cap shortly before installation. During installation, confirm that the diaphragm is not damaged. • During installation, ensure that the sealing surface of the instrument is clean and free from damage. • The instrument can only be screwed in or out with a wrench. Do not use the housing as a working surface. • The correct torque depends on the size of the process connection and the gasket (form/material) used. • Be careful not to thread when screwing in.
