YPQ101E工控备件机器人模块
具有冲洗隔膜
用于可能堵塞工艺连接孔的高粘度或结晶介质。安装和调试需要合格人员。不遵守规定会导致人身伤害或设备损坏。在安装、调试和操作之前，确保已根据测量范围、设计和特定测量条件选择了合适的压力开关。合格人员合格人员是指根据其技术培训、测量和控制技术知识以及对国家特定法规、现行标准和指令的经验和知识，能够实施所述工作并独立识别潜在危险的人员。最佳性能主题推荐安装第2页新的目录号1关于冲洗隔膜的安全注意事项下的新项目符号1 G 1/2 B冲洗隔膜添加到工艺连接表3 G 1/2 B的冲洗隔膜尺寸图添加到工艺接头尺寸3在制造机械连接部分4的开始处添加了新项目符号气体蒸汽液体2罗克韦尔自动化出版物836P-IN001B-EN-P-2017年12月显示固态压力开关。
规定的入口保护
仅适用于使用具有适当入口保护的匹配连接器插入的情况。相对压力测量范围为16 psi、1000 psi和1500 psi时，超压限值为1.7倍。其余可用型号两次。电源15…35 V直流电流消耗开关输出：模拟信号4…20 mA；70毫安；无模拟信号：45 mA带IO链路的总电流消耗：最大450 mA，包括开关电流输出类型2 x PNP、1 PNP和4…20 mA模拟零偏移调整最大量程的3%输出阈值OUT 1和OUT 2可单独调整输出模式可选-常开、常闭、窗口、，滞后输出电压（电源-1V）输出电流带IO链路：OUT1最大100 mA，OUT2最大250 mA负载模拟信号4…20 mA：≤ 0.5 kΩ使用寿命1亿次开关周期模拟信号稳定时间：3 ms开关输出：20 ms，IO链路精度数据模拟信号≤ 量程的±1.0%，包括非线性、滞后、零点偏移和端值偏差（对应于IEC 61298-2规定的测量误差）。在垂直安装位置校准，过程连接面朝下。
With flushing diaphragm
Used for high viscosity or crystallization media that may block the process connection holes. Qualified personnel are required for installation and commissioning. Failure to comply with the regulations may result in personal injury or equipment damage. Before installation, commissioning and operation, ensure that the appropriate pressure switch has been selected according to the measurement range, design and specific measurement conditions. Qualified personnel Qualified personnel refer to those who can perform the described work and independently identify potential hazards according to their technical training, measurement and control technical knowledge, and their experience and knowledge of specific national regulations, current standards and directives. Best Performance Topic Recommended Installation Page 2 New Catalog Number 1 New Bullet 1 G 1/2 B Flushing Diaphragm under Safety Precautions for Flushing Diaphragm Added to Process Connection Table 3 Flushing Diaphragm Dimension Drawing for G 1/2 B Added to Process Connection Dimension 3 New Bullet Gas Vapor Liquid 2 Rockwell Automation Publication 836P-IN001B-EN-P-2017 December Display Solid State Pressure Switch at the beginning of Manufacturing Mechanical Connection Section 4.
Specified entrance protection
This applies only when inserted using a mating connector with appropriate access protection. The overpressure limit is 1.7 times when the relative pressure measurement range is 16 psi, 1000 psi, and 1500 psi. Other models are available twice. Power supply 15... 35 V DC current consumption switch output: analog signal 4... 20 mA; 70 mA; No analog signal: 45 mA Total current consumption with IO link: maximum 450 mA, including switching current output type 2 x PNP, 1 PNP and 4... 20 mA Analog zero offset 3% of the maximum range Output threshold OUT 1 and OUT 2 can be adjusted independently Output mode options - normally open, normally closed, window, lagging output voltage (power supply - 1V) Output current with IO link: OUT1 Maximum 100 mA, OUT2 maximum 250 mA load analog signal 4... 20 mA: ≤ 0.5 k Ω service life 100 million switching cycles Analog signal stability time: 3 ms Switch output: 20 ms, IO link accuracy data analog signal ≤ ± 1.0% of the range, including nonlinearity, hysteresis, zero point offset and terminal value deviation (corresponding to the measurement error specified in IEC 61298-2). Calibrate in the vertical mounting position with the process connection face down.
