Honeywell 05701-A-0325工控备件机器人模块
数据铭牌
位于主控制板附近目录号系列标识符新主装置上的控制板例如，如果RGU的数据铭牌具有B系列标识符（或 CT电流监测），则新的主控制板应标有目录号-PMA！注意：如果存在任何电压，请拆下电压源。继续下一步前，再次检查电压。出版物F- 年月日RGU™ 主控制板更换固件版本图主控制板图拆卸安装通信板 至笔记本电脑（仅用于升级固件）至CANport设备至CANport设备至NTC桥接热传感器可用于用户连接至隔离板（J）至TE至栅极驱动器板（J）（模拟IO）安装螺钉支架连接端口连接盖出版物F- 年月RGU™ 主控制板更换固件版本 安装主控制板戴上ED腕带并将其连接到PE母线。
安装螺钉拧紧
安装之前从主控制板上拆下的所有通信板（如图所示）。将所有安装螺钉拧紧至 lb in（ N-m）。将主控制板向下滑动到滑动安装支架上。将主控制板安装到安装板上。将安装螺钉拧紧至 lb in（ N-m）。将TB连接到主控制板。确认所有端子牢固。连接J、J、J、J、J和J，如图所示。结束步骤安装主控制板后，从装置上移除所有工具和碎屑，并固定隔间门。将旧电路板送至自动化公司进行维修或根据贵公司的程序和当地条例处理电路板！注意：操作装置前必须配置参数。请参阅出版物F-的启动章节，以配置新主控制板中的参数。出版物F- 年月PN 取代出版物F--年月版权所有年国际公司。
Data plate
For example, if the data nameplate of the RGU has the B series identifier (or CT current monitoring), the new main control panel should be marked with the catalog number PMA! NOTE: If any voltage is present, remove the voltage source. Check the voltage again before proceeding to the next step. Publication F - Year Month Day RGU ™ Main Control Board Firmware Replacement Version Diagram Main Control Board Diagram Removing and Installing Communication Board to Laptop (Only for Firmware Upgrade) to CANport Device to CANport Device to NTC Bridging Thermal Sensor for Users to Connect to Isolation Board (J) to TE to Grid Driver Board (J) (Analog IO) Mounting Screw Bracket Connection Port Connection Cover Publication F - Month RGU ™ Replace the firmware version of the main control board Install the main control board, put on the ED wrist strap and connect it to the PE bus.
Tighten the mounting screws
Install all communication boards removed from the main control board before installation (as shown in the figure). Tighten all mounting screws to lb in (N-m). Slide the main control board down onto the sliding mounting bracket. Install the main control board onto the mounting plate. Tighten the mounting screws to lb in (N-m). Connect the TB to the main control board. Verify that all terminals are secure. Connect J, J, J, J, J, and J as shown. At the end of the procedure, after installing the main control panel, remove all tools and debris from the unit and secure the compartment door. Send the old circuit board to the automation company for repair or dispose of the circuit board according to your company's procedures and local regulations! Note: The parameters must be configured before operating the device. Refer to the Startup section of publication F - to configure the parameters in the new main control panel. Publication F - Year PN supersedes Publication F - Year Copyright International Corporation.
