PU516A 3BSE032402R1自动化模块
实施系统
注意：只有熟悉驱动系统、系统中使用的产品和相关机械的人员才能计划或实施系统的安装、启动和未来维护。不遵守规定可能导致人身伤害和/或设备损坏。注意：根据ANSI/NFPA 70E第二部分的要求，确认所有交流和直流电源均已断电、锁定或挂牌。注意：系统可能包含储能装置。为避免触电危险，在尝试维修、修理或拆卸驱动系统或其部件之前，请确认电容器上的所有电压已放电。只有在您有资格且熟悉固态控制设备和出版物NFPA 70E中的安全程序的情况下，才应尝试本手册中的程序。注意：维修任何装置时，请勿将任何螺母、螺栓、垫圈等掉落在装置内，因为它们可能会在通电时造成短路。注意：此驱动系统包含ESD（静电放电）敏感部件和组件。
控制预防措施
安装、测试或修理此组件时，需要采取静态控制预防措施。如果不遵守ESD控制程序，可能导致部件损坏。如果您不熟悉静电控制程序，请参阅Allen Bradley出版物8000-4.5.2《防止静电损坏》或任何其他适用的ESD保护手册。出版物2364F-5.13 1999年6月RGU™ 隔离板更换3初步步骤更换电源之前，请关闭电源；锁定/挂牌装置；并等待五分钟以使所有电压放电。打开电源结构的托架门。更换隔离板1.使用仪表测试交流线路、直流母线和隔离板上端子的电压。2.戴上ESD腕带并将其连接到PE母线（装置底部的后接地棒）
Implementation system
Note: Only personnel familiar with the drive system, products used in the system and related machinery can plan or implement the installation, startup and future maintenance of the system. Failure to comply may result in personal injury and/or equipment damage. NOTE: Confirm that all AC and DC power supplies are de energized, locked out, or tagged out in accordance with ANSI/NFPA 70E, Part II. Note: The system may contain energy storage devices. To avoid the danger of electric shock, before attempting to repair, repair or disassemble the drive system or its components, please confirm that all voltages on the capacitor have been discharged. The procedures in this manual should only be attempted if you are qualified and familiar with the safety procedures in solid state control equipment and publication NFPA 70E. Note: When repairing any device, do not drop any nut, bolt, washer, etc. into the device, because they may cause short circuit when energized. Note: This drive system contains ESD (electrostatic discharge) sensitive components and components.
Control precautions
Static control precautions are required when installing, testing, or repairing this component. Failure to follow ESD control procedures may result in component damage. If you are unfamiliar with static control procedures, refer to Allen Bradley publication 8000-4.5.2, "Preventing Electrostatic Damage," or any other applicable ESD protection manual. Publication 2364F-5.13 June 1999 RGU ™ Preliminary steps for replacing the isolation board 3 Turn off the power before replacing the power supply; Lock out/tag out device; Wait five minutes to discharge all voltages. Open the bay door of the power structure. Replace the isolation board 1. Use the instrument to test the voltage of AC lines, DC buses and terminals on the isolation board. 2. Wear ESD wrist strap and connect it to PE bus (rear grounding bar at the bottom of the device)
