HIMA F8627X 模拟量输出模块
隔离板
RGU隔离板表A：负载电阻器套件J7 1 J2 1 TB4 1 TB6 1 TB5 1 J1 1 P1 SW1 115V TB31 TB21 TB31*注：TB2仅用于B系列RGU（或RGU至交流线路至直流母线至主控制板（J12）至未使用的电流传感器T相负载电阻器（F17、F18、F19）S相负载电阻器*R相负载电阻器至控制电路电路由于铭牌显示这是一个a系列装置，TB2中不需要电阻器。a系列B出版物2364F-5.13 1999年6月RGU™ 隔离板更换5安装隔离板1.将负载电阻器固定在新板上的端子中（验证透明绝缘层没有进入端子）。拧紧至6 lb in（0.7 N-m）。注：TB2仅用于B系列RGU（见数据铭牌）。
固定电路板
将电路板放在六个支架上并固定电路板。3.将端子块TB5和TB6连接至隔离板。接线板必须牢固地压入适当的插座中。4.将反馈连接连接到J1，将带状电缆连接到J2，将电流传感器连接到J7，将PE地线连接到P1。5.将Lexan防护罩更换到隔离板上。6.验证SW1设置正确（115V AC）。结束步骤安装隔离板后，更换所有Lexan屏蔽并固定隔间门。将电路板送至自动化公司进行维修，或根据贵公司的程序和当地条例处理旧电路板！注意：SW1必须设置为适当的控制功率。将SW1设置为错误设置将导致隔离板和其他部件损坏。出版物2364F-5.13 1999年6月PN 192666取代出版物2364F-5.13 1999 1999年3月版权所有1999年国际公司。美国印刷Lexan是通用电气公司的商标
Isolation plate
RGU isolation board table A: load resistor kit J7 1 J2 1 TB4 1 TB6 1 TB5 1 J1 1 P1 SW1 115V TB31 TB21 TB31 * Note: TB2 is only used for B series RGU (or RGU to AC line to DC bus to main control board (J12) to unused current sensor T phase load resistor (F17, F18, F19) S phase load resistor * R phase load resistor to control circuit circuit Since the nameplate shows that this is a series device, no resistor is required in TB2. A Series B Publication 2364F-5.13 June 1999 RGU ™ Replace the isolation board 5 Install the isolation board 1. Fix the load resistor in the terminal on the new board (verify that the transparent insulating layer does not enter the terminal). Tighten to 6 lb in (0.7 N-m). Note: TB2 is only used for B series RGUs (see data nameplate).
Fixed circuit board
Place the circuit board on the six brackets and secure the circuit board. 3. Connect terminal blocks TB5 and TB6 to the isolation board. The terminal block must be firmly pressed into the appropriate socket. 4. Connect the feedback connection to J1, the ribbon cable to J2, the current sensor to J7, and the PE ground wire to P1. 5. Replace the Lexan shield onto the isolation plate. 6. Verify that SW1 is set correctly (115V AC). At the end of the step, replace all Lexan shields and secure the compartment door after installing the isolation panel. Send the circuit board to the automation company for maintenance, or dispose of the old circuit board according to your company's procedures and local regulations! Note: SW1 must be set to the appropriate control power. Setting SW1 to the wrong setting will cause damage to the isolation panel and other components. Publication 2364F-5.13 June 1999 PN 192666 replaces publication 2364F-5.13 March 1999 Copyright 1999 International Corporation. Printed in the United States Lexan is a trademark of General Electric Company
