IS200DSPXH2BEB工控备件
本说明中使用的警告
通知适用于可能导致人身伤害或死亡的危险或不安全行为。注意事项适用于可能导致财产损失的危险或不安全做法。注释强调了程序，并包含有助于操作员理解本说明中所含信息的信息。警告说明手册在未阅读、理解和遵循正确的贝利控制说明和手册的情况下，不得安装、维护或操作本设备；否则，可能导致人身伤害或损坏。射频干扰大多数电子设备都受到射频干扰（RFI）的影响。在便携式通信设备周围区域使用便携式通信设备时应谨慎。谨慎的做法规定，应在设备附近张贴警告使用便携式通信设备的标志。可能的工艺干扰维护必须由合格人员进行，且必须在固定本产品控制的设备后进行。在系统中调整或移除该产品可能会扰乱正在控制的过程。某些工艺干扰可能会造成伤害或损坏。
控制过程
调整和/或提取生产过程中可能发生的控制过程中的政变，这是一种系统行为。政变发生在幸福与幸福之间。注意本文件中包含的信息如有更改，恕不另行通知。贝利控制公司、其附属公司、员工和代理人，以及本出版物的作者和撰稿人，明确表示不承担任何明示和暗示的责任和保证（包括适销性和适用于特定目的的保证），和/或本文所含信息的可靠性和/或适用于任何特定用途和/或与用户/或依赖本文所含的信息整体或部分选择的任何材料和/或设备的性能。材料和/或设备的选择由本出版物用户自行承担风险。本文件包含贝利控制公司（Elsag Bailey Process Automation）的专有信息，并严格保密。禁止将其用于或复制用于本文所述硬件或软件的反向工程、开发或制造。未经贝利控制公司事先书面同意，不得影印或复制本文件的任何部分。WBPEEUI240752A0前言IMDSI1数字输入模块是一个接口，用于将16个单独的过程现场信号引入INFI 90®OPEN战略过程管理系统。控制模块使用这些数字输入来监视和控制过程。本说明说明了IMDSI12、IMDSI13、IMDSI14和IMDSI15模块的数字输入模块规格和操作。它详细介绍了完成模块的设置、安装、维护、故障排除和更换所需的程序。IMDSI12与现有IMDSI02模块功能等效，只是IMDSI2仅提供17毫秒的去抖动滤波器时间。使用正确的跳线设置，任何IMDSI1模块都可以直接替代IMDSI02模块。例如，IMDSI13模块可以替代IMDSI02模块，该模块的所有跳线都设置为24 VDC，并带有17毫秒的去抖动滤波器。使用IMDSI1数字输入模块的系统工程师或技术人员应在操作模块之前阅读并理解本说明。
Warnings used in this instruction
The notice is applicable to dangerous or unsafe behaviors that may cause personal injury or death. Precautions apply to hazardous or unsafe practices that may result in property damage. The notes highlight the procedure and contain information that will help the operator understand the information contained in this instruction. Warning instruction manual Do not install, maintain or operate this equipment without reading, understanding and following the correct Bailey control instructions and manuals; Failure to do so may result in personal injury or damage. Radio Frequency Interference (RFI) Most electronic devices are affected by Radio Frequency Interference (RFI). Use caution when using portable communication equipment in the area around the portable communication equipment. It is prudent to post signs warning of the use of portable communication equipment near the equipment. Possible process interference maintenance must be carried out by qualified personnel, and must be carried out after the equipment controlled by this product is fixed. Adjusting or removing the product in the system may disrupt the process being controlled. Some process disturbances may cause injury or damage.
Control process
It is a systematic behavior to adjust and/or extract the coup in the control process that may occur in the production process. The coup took place between happiness and happiness. Note that the information contained in this document is subject to change without notice. Bailey Controls, its affiliates, employees and agents, as well as the authors and contributors of this publication, expressly disclaim any express or implied responsibilities and warranties (including warranties of merchantability and fitness for a particular purpose), and/or the reliability of the information contained herein and/or the performance of any materials and/or equipment selected for any particular purpose and/or with users/or relying on the information contained herein in whole or in part. The selection of materials and/or equipment is at the user's own risk. This document contains proprietary information of Elsag Bailey Process Automation and is strictly confidential. It is prohibited to use or copy it for reverse engineering, development or manufacturing of hardware or software described herein. No part of this document may be photocopied or reproduced without the prior written consent of Bailey Controls. WBPEEUI240,752A0 Preface IMDSI1 digital input module is an interface for introducing 16 separate process field signals into INFI 90 ® OPEN strategic process management system. The control module uses these digital inputs to monitor and control the process. This description describes the specifications and operation of digital input modules for IMDSI12, IMDSI13, IMDSI14 and IMDSI15 modules. It details the procedures required to complete the setup, installation, maintenance, troubleshooting and replacement of the module. IMDSI12 has the same function as the existing IMDSI02 module, except that IMDSI2 only provides 17 ms of jitter removal filter time. With the correct jumper settings, any IMDSI1 module can directly replace the IMDSI02 module. For example, IMDSI13 module can replace IMDSI02 module. All jumpers of this module are set to 24 VDC and have a 17 millisecond jitter filter. The system engineer or technician using IMDSI1 digital input module should read and understand this instruction before operating the module.
